i have problem with loading cisco IOS c2960-lanbasek9-mz.150-2.SE9.bin.from flash. it's just show c2960-lanbasek9-mz.150-2.SE9.bin : no such device and then it boot old IOS c2960-lanbasek9-mz.122-55.SE11.bin from flash.
*Mar 1 00:07:48.919: %SYS-5-RELOAD: Reload requested by adminbn on console. Red Boot Sector Filesystem (bs) installed, fsid: 2 Base ethernet MAC Address: 00:26:ca:c9:60:00 Xmodem file system is available. The password-recovery mechanism is enabled. Initializing Flash... flashfs: 531 files, 19 directories flashfs: 0 orphaned files, 0 orphaned directories flashfs: Total bytes: 32514048 flashfs: Bytes used: 32081920 flashfs: Bytes available: 432128 flashfs: flashfs fsck took 21 seconds. ...done Initializing Flash. done. Loading "c2960-lanbasek9-mz.150-2.SE9.bin"...c2960-lanbasek9-mz.150-2.SE9.bin: e
Error loading "c2960-lanbasek9-mz.150-2.SE9.bin"
Interrupt within 5 seconds to abort boot process. Loading "flash:/c2960-lanbasek9-mz.122-55.SE11.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@ File "flash:/c2960-lanbasek9-mz.122-55.SE11.bin" uncompressed and installed, en0 executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(55)SE11, R) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2016 by Cisco Systems, Inc. Compiled Wed 17-Aug-16 13:46 by prod_rel_team Image text-base: 0x00003000, data-base: 0x01900000
Checking for Bootloader upgrade.. not needed POST: CPU MIC register Tests : Begin POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC interface Loopback Tests : Begin POST: CPU MIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin POST: PortASIC RingLoopback Tests : End, Status Passed
POST: PortASIC CAM Subsystem Tests : Begin POST: PortASIC CAM Subsystem Tests : End, Status Passed
POST: PortASIC Port Loopback Tests : Begin POST: PortASIC Port Loopback Tests : End, Status Passed
Waiting for Port download...Complete
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
i have problem with loading cisco IOS c2960-lanbasek9-mz.150-2.SE9.bin.from flash
I presume the "upgrade" means copying the BIN file into the switch? There's nothing wrong with it but in this case, the switch can't load it because the file has the incorrect filename and extension. I recommend using the more versatile "archive download-sw" command to upgrade the IOS (make sure to use the TAR file).
Question We run asr9001 with XR 6.1.3, and we have a very long delay to
login w/ SSH 1 or 2 to the device compare to IOS device. After
investigation, the there is 1s delay between the client KEXDH_INIT and
the server (XR) KEXDH_REPLY. After debug ssh serv...
Introduction The purpose of this document is to demonstrate the Open
Shortest Path First (OSPF) behavior when the V-bit (Virtual-link bit) is
present in a non-backbone area. The V-bit is signaled in Type-1 LSA only
if the router is the endpoint of one or ...
Hi, I am seeing quite a few issues with patch install and wanted to
share my experience and workaround to this. Login to admin via CLI, then
access root with the “shell” command Issue “df –h” and you’ll probably
see the following directory full or nearly ...