Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Error Messages

Hi all

i hve attached the log which i recd after reseting the router.pls revert bck wht may be the probs ,this is after upgrading the IOS.

2w0d: %SYS-5-RELOAD: Reload requested

System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1999 by cisco Systems, Inc.

TAC:Home:SW:IOS:Specials for info

C2600 platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x59421c

Self decompressing the image :

################################################################################################

[OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

000092 0X000B3280 C2600 Dual Ethernet

0X000F3BB0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X003B7E30

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 4Mb.

Using 12 percent iomem. [4Mb/32Mb]

tdm_eadi_post_configs: TDM Backplane not enabled

%SYS-2-MALLOCFAIL: Memory allocation of 32 bytes failed from 0x803C9578,

alignment 0

Pool: Processor Free: 0 Cause: Not enough free memory

Alternate Pool: None Free: 0 Cause: No Alternate pool

-Process= "ISDN", ipl= 0, pid= 60

-Traceback= 803C6E6C 803C8B7C 803C957C 8011F9E4 800E60D0 800CE81C 800CD2C8

800CE044 800E5A60 800BC230 800BC200

%SYS-2-NOBLOCK: printf with blocking disabled.

-Process= "Pool Manager", ipl= 0, pid= 5

-Traceback= 80325F44 803C6ED4 803C8B7C 80377824 803D42E8 803E91C4

*** System received a SegV exception ***

signal= 0xb, code= 0x1100, context= 0x81001758

PC = 0x2a8, Vector = 0x1100, SP = 0x810029a4

*** Unexpected Console FIFO timeout interrupt ***

PC = 0xfff03fc4, Vector = 0x500, SP = 0x8100294c

System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1999 by cisco Systems, Inc.

TAC:Home:SW:IOS:Specials for info

C2600 platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x59421c

Self decompressing the image :

################################################################################################

[OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

000092 0X000B3280 C2600 Dual Ethernet

0X000F3BB0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X003B7E30

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 4Mb.

Using 12 percent iomem. [4Mb/32Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-I-M), Version 12.2(8)T5, RELEASE SOFTWARE

(fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Fri 21-Jun-02 08:50 by ccai

Image text-base: 0x80008074, data-base: 0x80A2BD40

cisco 2611 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of

memory.

Processor board ID JAD041000Q9 (1641265025)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

Basic Rate ISDN software, Version 1.1.

2 Ethernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

1 ISDN Basic Rate interface(s)

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

regds

prem

2 REPLIES
New Member

Re: Error Messages

Is the router working fine after you put the new IOS? But some of your configuration may not be supported by the IOS, please check the IOS features.Also check if ISDN is working fine without any problem?

New Member

Re: Error Messages

Check the following URL on troubleshooting Memory Allocation error.

http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1831/products_tech_note09186a00800a6f3a.shtml

regards,

Bessie

172
Views
0
Helpful
2
Replies