Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Errors accessing slot0:

I'm trying to access sup-slot0: from either msfc on a 6509. Sups are 1As and msfcs are 1s. The 6509 is running hybred mode with Cat 6.3.5 on sups. I'm trying to copy IOS from slot0: to msfc bootflash and an receiving timeouts -

ho-ntc-rsw4> (enable) copy tftp:c6msfc-jsv-mz.121-8b.E11.bin slot0:

IP address or name of remote host [10.xxx.xxx.xxx]?

24772480 bytes available on device slot0, proceed (y/n) [n]? y

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

File has been copied successfully.

ho-ntc-rsw4> (enable) sess 16

Trying Router-16...

Connected to Router-16.

Escape character is '^]'.

ho-ntc-rsw4-msfc1(boot)#$ot0:c6msfc-jsv-mz.121-8b.E11.bin bootflash:

Destination filename [c6msfc-jsv-mz.121-8b.E11.bin]?

Accessing sup-slot0:c6msfc-jsv-mz.121-8b.E11.bin...

Loading slot0:c6msfc-jsv-mz.121-8b.E11.bin ...from 127.0.0.11 (via EOBC0/6): !

Loading slot0:c6msfc-jsv-mz.121-8b.E11.bin

Loading slot0:c6msfc-jsv-mz.121-8b.E11.bin

Loading slot0:c6msfc-jsv-mz.121-8b.E11.bin

Loading slot0:c6msfc-jsv-mz.121-8b.E11.bin

%Error opening sup-slot0:c6msfc-jsv-mz.121-8b.E11.bin (Timed out)

ho-ntc-rsw4-msfc1(boot)#

I've reformated pcmcia(s) and re-tftped IOS to same pcmcia(s) with same result, msfcs can't access slot0. Any ideas?

  • Other Network Infrastructure Subjects
2 REPLIES
Cisco Employee

Re: Errors accessing slot0:

Look at the following bug

http://www.cisco.com/cgi-bin/bugtool/onebug.pl?bugid=CSCdt17684

Why dont you use TFTP to download IOS into the MSFC bootflash?

New Member

Re: Errors accessing slot0:

I'm trying to run SRM on this switch. I have successfully tftped new IOS to active msfc (15). This msfc is the standby. Trying to follow the book which says to move the new IOS through slot0: Ref:Cat6000 Software Config Guide (22-45), for the standby msfc...

118
Views
0
Helpful
2
Replies
This widget could not be displayed.