Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

FlexWan EOS upgrade failed

Hi I upgrade the EOS in some FlexWan cards in 7609 equipments.

The EOS version I used is 0.28 (0x1c), 3 out of 4 worked fine, but with the last one the module got stucked, no answer. After investigating I realized that this module has a different hw version and most probably the min sw requirement was something higher than 0.28.

The question is how can force this module to boot from romon or is there any way to get the right sw version and put it into the card.

Your help is more than welcomed

Jorge

SLOT 9/0: 00:00:07: %EOS-2-EOS_INIT_FAILURE: The EOS FPGA initialization failed due to one of the QDR clocks not locked.

SLOT 9/0: 00:00:15: %EOS-2-NULL_EOS_OBJECT: The EOS device object pointer is set to NULL

SLOT 9/0: 00:00:15: %EOS-2-NULL_EOS_OBJECT: The EOS device object pointer is set to NULL

SLOT 9/0: 00:00:15: %EOS-2-NULL_EOS_OBJECT: The EOS device object pointer is set to NULL

SLOT 9/0: 00:00:15: %SLOT_FPD-3-GETVER_FAILED: Failed to get FPD version for FPD=2 in Slot 9: Cannot read version information.

SLOT 9/0: 00:00:16: %EOS-2-NULL_EOS_OBJECT: The EOS device object pointer is set to NULL

SLOT 9/0: 00:00:17: %SSA-5-FABRICSYNC_DONE: Fabric sync on Primary channel done.

SLOT 9/0: 00:00:17: %EOS-2-NULL_EOS_OBJECT: The EOS device object pointer is set to NULL

May 8 02:03:58: %DIAG-SP-6-RUN_COMPLETE: Module 9: Running Complete Diagnostics...

May 8 02:03:59: %SNMP-5-MODULETRAP: Module 9 [Down] Trap

May 8 02:03:59: %DIAG-SP-3-MAJOR: Module 9: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.

May 8 02:03:59: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 9: BusConnectivityTest failed

May 8 02:03:59: %OIR-SP-3-LC_FAILURE: Module 9 has Major online diagnostic failure, Card will be powered down. Please check bootflash diaginfo file for detailed diagnostic result.

May 8 02:04:09: %C6KPWR-SP-4-DISABLED: power to module in slot 9 set off (Diagnostic Failure)

2 REPLIES
New Member

Re: FlexWan EOS upgrade failed

hi

try out this one

upgrade hw-module slot X file sup-bootflash:filename

where X is the slot no of ur flexWAN

and check this link out for detail info

http://www.cisco.com/en/US/products/hw/routers/ps368/products_configuration_guide_chapter09186a0080440179.html

regards

Haris

New Member

Re: FlexWan EOS upgrade failed

Hi,

Where can I find the FPD sw, or EOS sw and how where can check/get the right version for my hw 2.0

I don't understand FDP and EOS difference and what they do?

164
Views
0
Helpful
2
Replies
CreatePlease login to create content