cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
502
Views
0
Helpful
1
Replies

Frame Relay to ATM Service Interworking Interoperability with switch Marcon

g.lanzafame
Level 1
Level 1

I am troubleshouting two router 7206-vxr connected throught an ATM cloud with switch Marconi.

Router A -- switch marconi A -- ATM Cloud -- switch marconi B -- Router B

a Router C(frame-relay with v35) is connected throught a frame-relay cloud to Switch A

I have 2 PVC in a test environment:

pvc 800( between router A and router B, connection ATM) is UP, while PVC 900 (that is a case of Frame Relay to ATM Service Interworking between a 7206-vxr and a 2600) is down.

The problem isolation is this: I verified that in the router CISCO7206vxr

OAM PVC management bring down the connection, using

debug atm oam

I obtained an output as

Nov 12 18:01:59.717: ATM OAM(ATM5/0.800): Timer: VCD#9 VC 10/800 Status:2 CTag:7

06 Tries:0

Nov 12 18:01:59.717: ATM OAM LOOP(ATM5/0.800) O: VCD#9 VC 10/800 CTag:2C3

Nov 12 18:01:59.721: ATM OAM LOOP(ATM5/0) I: VCD#9 VC 10/800 LoopInd:0 CTag:2C3

Nov 12 18:01:51.853: ATM OAM(ATM5/0.900): Timer: VCD#7 VC 10/900 Status:1 CTag:5

3138 Tries:2

Nov 12 18:01:51.853: ATM OAM LOOP(ATM5/0.900) O: VCD#7 VC 10/900 CTag:CF93

Nov 12 18:01:52.441: atm_oam_ais_inline(ATM5/0): AIS signal, failure=0x6A, VC 10

/700

I verified (WITH cTag) that end-to-end loopback cells for pvc 800 come from ROUTER B AND

I NEVER SEE (ON DEBUG ATM OAM) LOOPBACK CELL COMING FROM MARCONI SWITCH A

There is something to do with IOS software or with configurations of router?

It is only a problem of switch Marconi?

Information about router 7206vxr

IOS: c7200-js-mz.122-5.bin

sh running of router A (ROUTER B is simmetric)

...

cONFIGURATION OF PVC

interface ATM5/0.800 point-to-point

mtu 1500

bandwidth 2000

ip address 192.168.250.130 255.255.255.252

pvc ROUTERB 10/800

protocol ip 192.168.250.129

abr 2000 2000

oam-pvc manage

encapsulation aal5snap

!

!

interface ATM5/0.900 point-to-point

description "Link c"

mtu 1500

ip address 172.20.136.169 255.255.255.252

pvc ROUTERC 10/900

protocol ip 172.20.136.170

ubr 1900

oam-pvc manage

oam retry 3 5 1

encapsulation aal5snap

sh runn DI ROUTER c

interface Serial0

ip address 172.20.136.170 255.255.255.252

no ip mroute-cache

encapsulation frame-relay IETF

frame-relay map ip 172.20.136.169 900 broadcast

1 Reply 1

austinjw
Level 1
Level 1

You need to make sure on your point to point connection that you are using non-proprietary ATM protocols since you are using two different vendor products. The common standard is RFC1483.

Most vendor products default to their proprietary modes of operation. Cisco and Marconi do.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: