Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

from console not able to access my router

When i try to access my router from console it is showing the below status and hanged.

How can i reset my router physically? can anyone help me?

Thanks in advance

here are the putty results after restarted my router(1941 series)


System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2010 by cisco Systems, Inc.

Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
CISCO1941/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 64/-1(On-board/DIMM0) bit mode with ECC disabled


Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
program load complete, entry point: 0x80803000, size: 0x1b340


IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x2badc04
Self decompressing the image : #######################################################################################################################################################################################

Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x01E8F000
-----------------------------------------------
TOTAL: 0x01E8F000

Rounded IOMEM up to: 32Mb.
Using 6 percent iomem. [32Mb/512Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 16:26 by prod_rel_team
Image text-base: 0x2100A378, data-base: 0x24721AA0


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco CISCO1941/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FHK14467434
2 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)

Warning: flash0:flash0 does not exist. Command retained.
SETUP: new interface NVI0 placed in "shutdown" state


Press RETURN to get started!


*Mar 1 00:00:06.555: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c1900 Next reboot level
*Feb 15 00:13:14.599: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directo
*Feb 15 00:13:23.811: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
*Feb 15 00:13:23.815: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
*Feb 15 00:13:25.019: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to
*Feb 15 00:13:25.019: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to
*Feb 15 00:13:26.995: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
*Feb 15 00:13:31.695: %SYS-5-CONFIG_I: Configured from memory by console
*Feb 15 00:13:33.735: %LINK-5-CHANGED: Interface NVI0, changed state to administratively down
*Feb 15 00:13:34.295: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 16:26 by prod_rel_team
*Feb 15 00:13:34.375: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Feb 15 00:13:34.467: %SNMP-5-COLDSTART: SNMP agent on host R1 is undergoing a cold start
*Feb 15 00:13:35.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to down

 

63
Views
0
Helpful
0
Replies
CreatePlease to create content