Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

help,is it a protocol problem?

1142: *Apr 2 10:51:12: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet0/1 on VLAN0202. Port consistency restored.

2006 Apr 20 17:28:39 utc +08:00 %SPANTREE-2-PORTUNBLK: Unblock previously inc port 3/1 on VLAN 202

2006 Apr 20 17:28:39 utc +08:00 %SPANTREE-2-PORTUNBLK: Unblock previously inc port 3/1 on VLAN 114

51: Inconsistent local vlan.

50: *Mar 1 00:36:34: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet0/2 on vlan 114.

49: Inconsistent peer vlan.

48: *Mar 1 00:36:34: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet0/2 on vlan 202.

47: Received BPDU with inconsistent peer vlan id 202 on GigabitEthernet0/2 on vlan 114.

46: *Mar 1 00:36:34: %SPANTREE-2-RECV_PVID_ERR:

430: Inconsistent local vlan.

429: *Mar 1 06:54:08: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet0/1 on vlan 114.

428: Inconsistent peer vlan.

427: *Mar 1 06:54:08: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet0/1 on vlan 202.

426: Received BPDU with inconsistent peer vlan id 202 on GigabitEthernet0/1 on vlan 114.

425: *Mar 1 06:54:08: %SPANTREE-2-RECV_PVID_ERR:

1141: *Apr 2 10:50:57: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet0/1 on VLAN0114. Inconsistent local vlan.

1140: *Apr 2 10:50:57: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet0/1 on VLAN0202. Inconsistent peer vlan.

1139: *Apr 2 10:50:57: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent peer vlan id 202 on GigabitEthernet0/1 VLAN114.

2006 Apr 20 17:28:25 utc +08:00 %SPANTREE-2-TX_BLKPORTPVID: Block 3/1 on xmtting vlan 202 for inc peer vlan

2006 Apr 20 17:28:25 utc +08:00 %SPANTREE-2-RX_BLKPORTPVID: Block 3/1 on rcving vlan 114 for inc peer vlan 202

2006 Apr 20 17:28:25 utc +08:00 %SPANTREE-2-RX_1QPVIDERR: Rcved pvid_inc BPDU on 1Q port 3/1 vlan 114

1 ACCEPTED SOLUTION

Accepted Solutions

Re: help,is it a protocol problem?

Hi Friend,

Yes this could be an issue as connecting a hub or even a cross over cable between 2 ports in different vlans can result in this kind of problem and to be frank it is really difficult to find out in a big network.

You just need to check the errors and follow the ports and trace it out.

Check this link for all kind of spanning tree error messages and what they mean and how to troubleshoot them. This link has all the errors which were reported in your logs

http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_system_message_guide_chapter09186a008009e7a1.html#353669

HTH, if yes please rate the post.

Ankur

5 REPLIES

Re: help,is it a protocol problem?

Hi Friend,

I already tried to put it into your last post. No its not a protocol problem and mostly the problem is with configuration.

Anways can you check the native vlan config on the trunk ports? Or is possible post the config for trunk from both the switches

Regards,

Ankur

Community Member

Re: help,is it a protocol problem?

distribute layer switch:

hqjr12_cat3550_1#show int trunk

Port Mode Encapsulation Status Native vlan

Fa0/3 on 802.1q trunking 1

Fa0/4 on 802.1q trunking 1

Fa0/5 on 802.1q trunking 1

Fa0/6 on 802.1q trunking 1

Fa0/11 on 802.1q trunking 1

Fa0/12 on 802.1q trunking 1

Fa0/13 on 802.1q trunking 1

Fa0/16 on 802.1q trunking 1

Fa0/18 on 802.1q trunking 1

Gi0/1 on 802.1q trunking 1

core layer switch:

CNC-6506-L2-1> (enable) show port trunk

* - indicates vtp domain mismatch

Port Mode Encapsulation Status Native vlan

-------- ----------- ------------- ------------ -----------

1/1 on dot1q trunking 1

3/1 on dot1q trunking 1

3/3 on dot1q trunking 203

3/8 on dot1q trunking 1

15/1 nonegotiate isl trunking 1

16/1 nonegotiate isl trunking 1

Re: help,is it a protocol problem?

Hi Friend,

I think you are getting an error on

Gi0/1 on 802.1q trunking 1

3/1 on dot1q trunking 1 on different switch

Can you paste the complete config related to these ports from the 2 switches? as what all vlans are allowed on the trunks and other stuff , just paste all port related configs for these 2 ports only.

Regards,

Ankur

Community Member

Re: help,is it a protocol problem?

the native vlan is the same,however the crisis stop after all the clerk left,i thought it's not a misconfigeration,maybe someone connect two vlan togather using a hub or something,am i right?

could you tell me how can i find it,which kind of command is useful for me or send me a link,

thank you my dear friend

Re: help,is it a protocol problem?

Hi Friend,

Yes this could be an issue as connecting a hub or even a cross over cable between 2 ports in different vlans can result in this kind of problem and to be frank it is really difficult to find out in a big network.

You just need to check the errors and follow the ports and trace it out.

Check this link for all kind of spanning tree error messages and what they mean and how to troubleshoot them. This link has all the errors which were reported in your logs

http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_system_message_guide_chapter09186a008009e7a1.html#353669

HTH, if yes please rate the post.

Ankur

404
Views
0
Helpful
5
Replies
CreatePlease to create content