HELP Monitor port 761 router

simonwj · ‎02-25-2003

Help

I need to configfure two 761 routers before tomorrow. Its 9pm here.

Im trying to find the pinouts to make a console cable.

db9 to db9

hope someone can help

regards

Simon

7rbowenii · ‎02-25-2003

Hey Simon,

Try this:

http://www.cisco.com/en/US/customer/products/hw/routers/ps331/products_installation_guide_chapter09186a008007d017.html

-Bo

simonwj · ‎02-25-2003

thanks for your reply.

clicked on the link and it says im not logged in even though i had to be to post the thread in the forum.

only registered this afternoon.

is there something im missing

thanks Bo

7rbowenii · ‎02-25-2003

Try dis...

Specifications

Downloads

Specifications

Table of Contents

Specifications

Router Specifications

Port Pinouts

Ethernet Port

Serial Configuration Port

Power Connector

Common Port Assignments

Specifications

This chapter provides the specifications for your router and companion equipment.

Router Specifications

The specifications for Cisco 700 series routers are listed in Table A-1.

Table A-1: Hardware Specifications Description Design Specification

Height x Width x Depth

1.6 x 8.3 x 9.6 in. (4.1 x 21.1 x 24.4 cm)

Weight

Cisco 761 and Cisco 771: 1.4 lb. (0.6 kg)

Cisco 762 and Cisco 772: 1.5 lb. (0.7 kg)

Cisco 765 and Cisco 775: 1.6 lb. (0.7 kg)

Cisco 766 and Cisco 776: 1.7 lb. (0.8 kg)

Power supply

Voltage

Frequency

External

100 or 250 VAC

50 to 60 Hz

Processor

25-MHz 80386

Memory

1.5 MB of primary memory

1.0 MB of Flash memory

16 KB of NVRAM

Operating temperature

32 to 120ºF (0 to 50ºC)

Storage temperature

-30 to 160ºF (-35 to 70ºC)

Operating humidity

20 to 95%, noncondensing

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Port Pinouts

The router ports are industry standard, unless otherwise noted in this section. Figure 1-3 in "Overview," lists the ports by model.

Ethernet Port

Table A-2 compares the pinouts of the Ethernet port depending on the position of the HUB/NODE switch.

Table A-2: Ethernet Connector Pinouts (RJ-45) Pin Function (HUB/NODE switch in HUB Position) Function (HUB/NODE Switch in NODE Position or the Unmanaged Hub on Cisco 766 and 776 routers)

1

TX+

RX+

2

TX-

RX-

3

RX+

TX+

4

Unused

5

Unused

6

RX-

TX-

7

Unused

8

Unused

Serial Configuration Port

Table A-3 shows the pinouts for the configuration port.

Table A-3: Configuration Port Pinouts (DB-9) Pin Function

1

Carrier Detect (CD)

2

Received Data (RXD)

3

Transmitted Data (TXD)

4

Data Terminal Ready (DTR)

5

Signal Ground

6

Data Set Ready (DSR) input

7

Not used

8

Not used

9

Not used

The console port is configured as a data communications equipment (DCE) device. The default parameters for the console port are as follows:

Bits per second = 9600

Data bits = 8

Parity = None

Stop bits = 1

Power Connector

Table A-4 shows the pinouts for the router power connector, and, Figure A-1 shows the location of the power connector pins.

simonwj · ‎02-25-2003

Thanks

already found that, but what im looking for it the db9-db9 connections.

ie pin 2 - pin3

pin 3 - pin2

pin5 - pin5

etc

thanks

simonwj · ‎02-25-2003

thanks for everyones help

got it sorted bt trial and error.

the cable needed is straight through

thanks again

simon