Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Help on Debug

Hi Friends,

I am getting the below error messages in my ROuter Logs.can any one help me explain me and give a solution for this.

2d04h: %AMDP2_FE-3-UNDERFLO: Ethernet0/1 transmit error

2d05h: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/0 TDR=1, TRC=0

4 REPLIES
New Member

Re: Help on Debug

2d04h: %AMDP2_FE-3-UNDERFLO: Ethernet0/1 transmit error

While transmitting a frame, the local buffer of the controller chip received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally, such a problem is temporar y, depending on transient peak loads within the system. The system should recover.

2d05h: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/0 TDR=1, TRC=0

Ethernet or Fast Ethernet is detecting multiple collisions. This condition may occur under heavy loads. The system should recover.

Refer the following site for information

http://www.cisco.com/univercd/cc/td/doc/product/software/ios112/fgemf.htm

-Deepu

New Member

Re: Help on Debug

hank You all for the Valuable Responses.

Rgds

Srini

New Member

Re: Help on Debug

Hi there follow this link to the error message decoder , it will tell you exactly what the problem is if any:

http://www.cisco.com/cgi-bin/Support/Errordecoder/home.pl

The following is the feedabck from the decoder with regard to your error's.

1. %AMDP2_FE-3-UNDERFLO: [chars], transmit error

While transmitting a frame, the local buffer of the controller chip received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally, such a problem is temporar y, depending on transient peak loads within the system. The system should recover.

Recommended Action: No action is required.

Related documents: No specific documents apply to this error message.

2. %AMDP2_FE-3-UNDERFLO: AMDP2/FE [chars], Transmit underflow

While transmitting a frame, the local buffer of the controller chip has received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally, such a problem i s temporary, depending on transient peak loads within the system.

Recommended Action: The system should recover. No action is required

Related documents: No specific documents apply to this error message.

New Member

Re: Help on Debug

Hi,

For this warning message in console

2d04h: %AMDP2_FE-3-UNDERFLO: Ethernet0/1 transmit error

%AMDP2_FE-3-UNDERFLO: [chars], transmit error

While transmitting a frame, the local buffer of the controller chip received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally, such a problem is temporar y, depending on transient peak loads within the system. The system should recover.

Recommended Action: No action is required.

For this warning message:

2d05h: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/0 TDR=1, TRC=0

%AMDP2_FE-6-EXCESSCOLL: [chars] TDR=[dec], TRC=[dec]

Ethernet or Fast Ethernet is detecting multiple collisions. This condition may occur under heavy loads. The system should recover.

Recommended Action: No action is required.

The above 2 warning message won't affect your router functionality and performation and it should recover automatically.

Regards

Kiruba

240
Views
0
Helpful
4
Replies