11-27-2003 11:45 PM - edited 03-02-2019 12:01 PM
Hello Colleagues,
I'm trying to apply LLQ on ATM pvc on my 827-4V adsl router. Config is like this:
!
class-map match-all adsl-voip-traff
match access-group 100
!
policy-map VOIP
class adsl-voip-traff
priority 320
class class-default
fair-queue
policy-map ADSL-OUT
class class-default
shape average 1024000
service-policy VOIP
!
First problem is that the 'shape average' command accepted, but not entered in config (i can't see it by 'sh run' or by 'show policy' command').
And the second is, when I'trying to apply ADSL-OUT to
interface:
!
interface ATM0.1 point-to-point
ip unnumbered Loopback0
pvc 1/50
encapsulation aal5snap
!
the 'service-policy output ADSL-OUT' command accepted but policy not working. I tried enter this command under pvc configuration, under ATM0.1 configuration and even and ATM0 configuration mode, the result is the same. Also I tried to apply VOIP police instead of ADSL-OUT, the result is the same, but in logs cisco write
'16:14:00: I/f ATM0.1 VC 1/50 class adsl-voip-traff requested bandwidth 320 (kbps) Available only 0 (kbps)'
and policy not working.
Can anybody explain me this strange behavior??
Thank you for advance.
---------------
Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-V6Y6-M), Version 12.2(8)T5, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 20-Jun-02 21:29 by ccai
Image text-base: 0x80013170, data-base: 0x80971A7C
ROM: System Bootstrap, Version 12.2(4r)XM2, RELEASE SOFTWARE (fc1)
borisov-adsl uptime is 1 day, 14 hours, 39 minutes
System returned to ROM by power-on
System image file is "flash:c820-v6y6-mz.122-8.T5.bin"
CISCO C827-4V (MPC855T) processor (revision 0x502) with 31744K/1024K bytes of memory.
Processor board ID JAD05290X0V (2280422715), with hardware revision 0000
CPU rev number 5
Bridging software.
4 POTS Ports
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)
Configuration register is 0x2102
ATM0.1 is up, line protocol is up
Hardware is PQUICC_SAR (with Alcatel ADSL Module)
Interface is unnumbered. Using address of Loopback0 (5.5.5.5)
MTU 1500 bytes, BW 640 Kbit, DLY 80 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
203370 packets input, 103167780 bytes
182331 packets output, 31004446 bytes
0 OAM cells input, 0 OAM cells output
AAL5 CRC errors : 0
AAL5 Oversized SDUs : 0
11-28-2003 01:03 AM
Hello,
I think that, since you are using the IP feature pack, you need IOS version 12.2(8)YJ to support LLQ.
Regards,
Georg
11-28-2003 01:16 AM
Hello
Software (C820-V6Y6-M), Version 12.2(8)T5 = 12.2(8)T5 IP/VOICE IOS
So, I think I'm using IP feature pack.
You mean that LLQ is not supported in T IOS train?
11-28-2003 01:43 AM
Hello,
sorry, what I meant was that you are not using the IP Plus feature pack, and I think LLQ support for non IP Plus feature packs was introduced in 12.2(8)YJ.
Regards,
Georg
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: