Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

How to find IP of SUP card from MSFC in Catalyst 6509 switch

I have logged into the MSFC of 6509, and want to login to the SUP engine. I don't know the IP of SUP. Is there any way I can get the info from MSFC so that I can login to SUP or is there any command on MSFC like session <mod number> which we use to login to MSFC from SUP.

7 REPLIES
Cisco Employee

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Hi Sourabh,

Are you running your switch in HYBRID mode is yes can you give a try with "sh cdp nei det" command as I remember that we can see the sup from MSFC via CDP on Hybrid mode.

Try that and update if that works.

Regards,

Ankur

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Hi Ankur,

switch is running in HYBRID mode.

when i do sh cdp nei det on MSFC, i am not getting any entry displayed, so i believe that we cant see sup from msfc via CDP

Regards

Sourabh

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Guys,

any thoughts ?

appreciate your help !

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Hi

i think u can get it through sh cdp nei det

below is the output my 6509.

MDD-Router#sh cdp neighbors detail

-------------------------

Device ID: SCA0520022G(6509)

Entry address(es):

IP address: xxxx.xxx.xx.x

Platform: WS-C6509, Capabilities: Trans-Bridge Switch

Interface: Vlan1, Port ID (outgoing port): 15/1

Holdtime : 172 sec

Version :

WS-C6509 Software, Version McpSW: 8.3(5) NmpSW: 8.3(5)

Copyright (c) 1995-2004 by Cisco Systems

advertisement version: 2

VTP Management Domain: 'xxxxxxx'

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Hi,

There is no entry for any device when i do sh cdp nei on MSFC.

I have checked that CDP is running on switch.

Router>sh process | incl CDP

41 Mwe 404232D0 28 18769 1 5428/6000 0 CDP Protocol

Purple

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Sure its not a native box ???? If it was a hybrid it "would" show in cdp even if the fields were blank. See if you can do a show mod command and post . Also a show version might help.

Re: How to find IP of SUP card from MSFC in Catalyst 6509 switch

Hi,

Switch is running in hybrid mode. here is the output of sh mod and sh ver.

Switch> sh module

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

2 2 24 100BaseFX MM Ethernet WS-X6324-100FX-MM no ok

3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAL08144HGQ

15 SAL0811W7M0

2 SAD05400437

3 SAL050212BD

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-0f-8f-9d-27-92 to 00-0f-8f-9d-27-93 5.0 7.1(1) 6.3(10)

00-0f-8f-9d-27-90 to 00-0f-8f-9d-27-91

00-07-84-f6-6a-c0 to 00-07-84-f6-6e-bf

15 00-0f-34-39-fc-c0 to 00-0f-34-39-fc-ff 2.6 12.1(13)E1 12.1(13)E12

2 00-03-32-85-6f-ec to 00-03-32-85-70-03 3.0 5.4(2) 6.3(10)

3 00-05-5f-2a-83-08 to 00-05-5f-2a-83-37 3.1 5.4(2) 6.3(10)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- ----------------------- ------------------- ----------- ------

1 L3 Switching Engine II WS-F6K-PFC2 SAL08144GQM 3.4

Router>sh ver

Cisco Internetwork Operating System Software

IOS (tm) MSFC2 Software (C6MSFC2-DSV-M), Version 12.1(13)E12, EARLY DEPLOYMENT R

ELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Sat 22-Nov-03 07:16 by hqluong

Image text-base: 0x40008C00, data-base: 0x419F4000

ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)

BOOTLDR: MSFC2 Software (C6MSFC2-BOOT-M), Version 12.1(13)E12, EARLY DEPLOYMENT

RELEASE SOFTWARE (fc1)

Router uptime is 2 days, 4 hours, 31 minutes

System returned to ROM by power-on

System image file is "bootflash:c6msfc2-dsv-mz.121-13.E12.bin"

cisco Cat6k-MSFC2 (R7000) processor with 458752K/65536K bytes of memory.

Processor board ID SAL0811W7M0

R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

509K bytes of non-volatile configuration memory.

32768K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x102

725
Views
0
Helpful
7
Replies
CreatePlease login to create content