09-18-2006 01:00 AM - edited 03-03-2019 05:05 AM
I have logged into the MSFC of 6509, and want to login to the SUP engine. I don't know the IP of SUP. Is there any way I can get the info from MSFC so that I can login to SUP or is there any command on MSFC like session <mod number> which we use to login to MSFC from SUP.
09-18-2006 01:05 AM
Hi Sourabh,
Are you running your switch in HYBRID mode is yes can you give a try with "sh cdp nei det" command as I remember that we can see the sup from MSFC via CDP on Hybrid mode.
Try that and update if that works.
Regards,
Ankur
09-18-2006 01:28 AM
Hi Ankur,
switch is running in HYBRID mode.
when i do sh cdp nei det on MSFC, i am not getting any entry displayed, so i believe that we cant see sup from msfc via CDP
Regards
Sourabh
09-19-2006 10:32 PM
Guys,
any thoughts ?
appreciate your help !
09-20-2006 02:51 AM
Hi
i think u can get it through sh cdp nei det
below is the output my 6509.
MDD-Router#sh cdp neighbors detail
-------------------------
Device ID: SCA0520022G(6509)
Entry address(es):
IP address: xxxx.xxx.xx.x
Platform: WS-C6509, Capabilities: Trans-Bridge Switch
Interface: Vlan1, Port ID (outgoing port): 15/1
Holdtime : 172 sec
Version :
WS-C6509 Software, Version McpSW: 8.3(5) NmpSW: 8.3(5)
Copyright (c) 1995-2004 by Cisco Systems
advertisement version: 2
VTP Management Domain: 'xxxxxxx'
09-20-2006 03:15 AM
Hi,
There is no entry for any device when i do sh cdp nei on MSFC.
I have checked that CDP is running on switch.
Router>sh process | incl CDP
41 Mwe 404232D0 28 18769 1 5428/6000 0 CDP Protocol
09-20-2006 03:29 AM
Sure its not a native box ???? If it was a hybrid it "would" show in cdp even if the fields were blank. See if you can do a show mod command and post . Also a show version might help.
09-20-2006 03:40 AM
Hi,
Switch is running in hybrid mode. here is the output of sh mod and sh ver.
Switch> sh module
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok
15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok
2 2 24 100BaseFX MM Ethernet WS-X6324-100FX-MM no ok
3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
Mod Module-Name Serial-Num
--- -------------------- -----------
1 SAL08144HGQ
15 SAL0811W7M0
2 SAD05400437
3 SAL050212BD
Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-0f-8f-9d-27-92 to 00-0f-8f-9d-27-93 5.0 7.1(1) 6.3(10)
00-0f-8f-9d-27-90 to 00-0f-8f-9d-27-91
00-07-84-f6-6a-c0 to 00-07-84-f6-6e-bf
15 00-0f-34-39-fc-c0 to 00-0f-34-39-fc-ff 2.6 12.1(13)E1 12.1(13)E12
2 00-03-32-85-6f-ec to 00-03-32-85-70-03 3.0 5.4(2) 6.3(10)
3 00-05-5f-2a-83-08 to 00-05-5f-2a-83-37 3.1 5.4(2) 6.3(10)
Mod Sub-Type Sub-Model Sub-Serial Sub-Hw
--- ----------------------- ------------------- ----------- ------
1 L3 Switching Engine II WS-F6K-PFC2 SAL08144GQM 3.4
Router>sh ver
Cisco Internetwork Operating System Software
IOS (tm) MSFC2 Software (C6MSFC2-DSV-M), Version 12.1(13)E12, EARLY DEPLOYMENT R
ELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Sat 22-Nov-03 07:16 by hqluong
Image text-base: 0x40008C00, data-base: 0x419F4000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: MSFC2 Software (C6MSFC2-BOOT-M), Version 12.1(13)E12, EARLY DEPLOYMENT
RELEASE SOFTWARE (fc1)
Router uptime is 2 days, 4 hours, 31 minutes
System returned to ROM by power-on
System image file is "bootflash:c6msfc2-dsv-mz.121-13.E12.bin"
cisco Cat6k-MSFC2 (R7000) processor with 458752K/65536K bytes of memory.
Processor board ID SAL0811W7M0
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
509K bytes of non-volatile configuration memory.
32768K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x102
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: