Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

HSRP Config

Hello,

cann somone tell me if this config is ok ? both router are Red. connected on 2 ISP 7500 series and on 2 Cisco 535 PIX

thanks for help

Router1#

interface FastEthernet0/0

description Connection to ISP

ip address 213.60.26.5 255.255.255.224

ip verify unicast reverse-path

no ip redirects

no ip route-cache

no ip mroute-cache

No ip proxy-arp

No cdp enable

No ip directed-broadcast

No ip unreachable

speed 100

full-duplex

standby 1 ip 213.60.26.4 255.255.255.224

standby 1 timers 3 10

standby 1 priority 105 preempt

standby 1 authentication eth_r1r2

standby 1 track Fastethernet 0/1

!

interface FastEthernet0/1

description Connection to PIX1

ip address 213.60.26.34 255.255.255.224

no ip redirects

no ip route-cache

no ip mroute-cache

No ip proxy-arp

No cdp enable

No ip directed-broadcast

No ip unreachable

speed 100

full-duplex

standby 1 ip 213.60.26.33

standby 1 timers 3 10

standby 1 priority 105 preempt

standby 1 authentication eth_r1r2

standby 1 track Fastethernet 0/0

-------------------------------------------

Router2#

interface FastEthernet0/0

description Connection to ISP

ip address 213.60.26.6 255.255.255.224

ip verify unicast reverse-path

no ip redirects

no ip route-cache

no ip mroute-cache

No ip proxy-arp

No cdp enable

No ip directed-broadcast

No ip unreachable

speed 100

full-duplex

standby 1 ip 213.60.26.4 255.255.255.224

standby 1 timers 3 10

standby 1 priority 105 preempt

standby 1 authentication eth_r1r2

standby 1 track Fastethernet 0/1

!

interface FastEthernet0/1

description Connection to PIX2

ip address 213.60.26.35 255.255.255.224

no ip redirects

no ip route-cache

no ip mroute-cache

No ip proxy-arp

No cdp enable

No ip directed-broadcast

No ip unreachable

speed 100

full-duplex

standby 1 ip 213.60.26.33

standby 1 timers 3 10

standby 1 priority 105 preempt

standby 1 authentication eth_r1r2

standby 1 track Fastethernet 0/0

3 REPLIES
New Member

Re: HSRP Config

Are you using any Layer 2 Switch in the path to connect to Pix / Routers and Routers to ISP Routers

I mean like this

Router1 Fa0/1-- L2 Switch --PIX1

Router2 Fa0/1-- L2 Switch --PIX2

Same way while conecting Fa0/0 towards ISP routers.

(Here L2 switch only one Switch)

Also are you using PIX in redundant mode

New Member

Re: HSRP Config

Router1 Fa0/1-- L2 Switch --PIX1 (yes)

Router2 Fa0/1-- L2 Switch --PIX2 (yes)

Same way while conecting Fa0/0 towards ISP routers. (yes)

(Here L2 switch only one Switch) (yes)

Also are you using PIX in redundant mode (yes)

New Member

Re: HSRP Config

Perfect,

So your configuration should work fine, providing redundancy for LAN/WAN link failure of the the router or PIX failure.

96
Views
0
Helpful
3
Replies
CreatePlease to create content