Re: Installing WIC 2T into a 3620

ksass · ‎06-27-2002

I am attempting to install 2 WIC 2T's into a 3620, I have tried 5 different IOS's and still cannot get the router to even recognize the WIC cards. I have tried 12.2.10a, 12.2.1, 12.1.5T, and 12.2.8T. The router has 48mb of mem and 16mb of flash. Ideas anyone???????

donewald · ‎06-27-2002

The following is the min versions for the WIC-2T's on the 3621's.

12.0(7)XK, 12.1(1)T, 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT,

12.2(8)T

Are you certain you've got the correct part numbers on this WIC and correct platform? For example if you've got a 3631 only 12.2(2)XT1 is supported. Also there are certain Network Modules that are needed for support, according to the documentation. The WIC-2T and WIC-A/S are supported on the Cisco 3600 (on the NM-1FE2W, NM-2FE-2W, NM-2W, and the NM-1FE1R2W network modules). So, if you don't have one of these this might also be your issue.

Link for your information as well:

http://www.cisco.com/univercd/cc/td/doc/pcat/sewn__y2.htm

Hope this helps,

Don

ksass · ‎06-27-2002

Here is what is currently running . I am not sure how to check 3621/31 What is the difference from a 3620??

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3620-IS-M), Version 12.1(5)T12, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Compiled Mon 04-Feb-02 09:38 by ccai

Image text-base: 0x60008950, data-base: 0x61132000

ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

CoralWay-Router uptime is 2 hours, 19 minutes

System returned to ROM by reload

System restarted at 09:33:12 edt Thu Jun 27 2002

System image file is "slot0:c3620-is-mz.121-5.T12.bin"

cisco 3620 (R4700) processor (revision 0x81) with 45056K/4096K bytes of memory.

Processor board ID 07661109

R4700 CPU at 80Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

Basic Rate ISDN software, Version 1.1.

1 Ethernet/IEEE 802.3 interface(s)

2 Serial network interface(s)

4 ISDN Basic Rate interface(s)

Integrated NT1's for 4 ISDN Basic Rate interfaces

DRAM configuration is 32 bits wide with parity disabled.

29K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

16384K bytes of processor board PCMCIA Slot0 flash (Read/Write)

Configuration register is 0x2102

donewald · ‎06-27-2002

it appears that your NM is not able to support these WICs. From your Show diag this is what you have.

Slot 0: NM-1E2W ---> Will not support your configuration according to previous link I sent.

Slot 0: WIC-1DSU-T1

Slot 1: WIC-1DSU-T1

Hope this helps,

Don

Slot 1: NM-4B-U