Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Insufficient memory to boot image when adding new module for 3661 router

I recently bought two 2 10/100 Fastethernet 2 WAN Card (NM-2FE2W) and slot it into slot 4 and 5 of my 3661 router.

When I boot up the router it comes with this meesage which I think prompts me to uograde my router memory.

I need advice on what type of memory should I buy and what will be the recommended capacity of memory should I buy to cater for this. I am also planning to slot in ISDN cards on the last slot -slot 6

If it got something to do with my config or the current modules in the slots then please help me out.

I have also added the SHOW DIAG and SHOW VER of my router for further information

program load complete, entry point: 0x80008000, size: 0x5be49c

Self decompressing the image : ################################################]

Smart Init is disabled. IOMEM set to: 15

Using iomem percentage: 15

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

ITC_Services#sho ver

===============================

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3660-I-M), Version 12.2(5a), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Thu 04-Oct-01 22:21 by pwade

Image text-base: 0x600089C0, data-base: 0x60A60000

ROM: System Bootstrap, Version 12.0(6r)T, RELEASE SOFTWARE (fc1)

ITC_Services uptime is 23 minutes

System returned to ROM by power-on

System image file is "flash:c3660-i-mz.122-5a.bin"

cisco 3660 (R527x) processor (revision 1.0) with 28672K/4096K bytes of memory.

Processor board ID JAB0549801G

R527x CPU at 225Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache

Bridging software.

X.25 software, Version 3.0.0.

3660 Chassis type: ENTERPRISE

1 FastEthernet/IEEE 802.3 interface(s)

8 Serial network interface(s)

16 terminal line(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

ITC_Services# sho diag

===============================

3660 Chassis type: ENTERPRISE

c3600 Backplane EEPROM:

Hardware Revision : 1.0

Top Assy. Part Number : 800-04740-02

Board Revision : C0

Deviation Number : 0-0

Fab Version : 02

PCB Serial Number : HAD04471SGX

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Chassis Serial Number : JAB0549801G

Chassis MAC Address : 0007.85bf.34c0

MAC Address block size : 112

Manufacturing Test Data : 00 00 00 00 00 00 00 00

Fab Part Number : 28-2651-02

Number of Slots : 6

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 C8 41 01 00 C0 46 03 20 00 12 84 02

0x10: 42 43 30 80 00 00 00 00 02 02 C1 8B 48 41 44 30

0x20: 34 34 37 31 53 47 58 03 00 81 00 00 00 00 04 00

0x30: C2 8B 4A 41 42 30 35 34 39 38 30 31 47 C3 06 00

0x40: 07 85 BF 34 C0 43 00 70 C4 08 00 00 00 00 00 00

0x50: 00 00 85 1C 0A 5B 02 01 06 FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Slot 0:

C3600 Mother board 1FE(TX) Port adapter, 1 port

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

PCB Serial Number : JAB05440FND

Processor type : 34

Top Assy. Part Number : 800-05293-04

Board Revision : C0

Fab Part Number : 28-3234-02

Deviation Number : 65535-65535

Manufacturing Test Data : FF FF FF FF FF FF FF FF

RMA Number : 255-255-255-255

RMA Test History : FF

RMA History : FF

Field Diagnostics Data : FF FF FF FF FF FF FF FF

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 4A 41 42 30 35 34 34 30 46 4E 44 09

0x10: 34 40 00 DA C0 46 03 20 00 14 AD 04 42 43 30 85

0x20: 1C 0C A2 02 80 FF FF FF FF C4 08 FF FF FF FF FF

0x30: FF FF FF 81 FF FF FF FF 03 FF 04 FF C5 08 FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00

Slot 1:

Mueslix-4T Port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision J0

Serial number 26536025 Part number 800-02314-02

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 54 01 01 01 94 E8 59 50 09 0A 02 00 00 00 00

0x30: 98 00 00 00 01 11 29 00 00 05 FF FF FF FF FF FF

Slot 2:

Mueslix-4T Port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision J0

Serial number 26553974 Part number 800-02314-02

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 54 01 01 01 95 2E 76 50 09 0A 02 00 00 00 00

0x30: 98 00 00 00 01 10 17 00 00 05 FF FF FF FF FF FF

Slot 3:

Analog Modem Port adapter, 16 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.0 Board revision F0

Serial number 29089157 Part number 800-02841-02

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 6F 01 00 01 BB DD 85 50 0B 19 02 00 00 00 00

0x30: 78 00 00 00 02 09 24 17 FF FF FF FF FF FF FF FF

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3660-I-M), Version 12.2(5a), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Thu 04-Oct-01 22:21 by pwade

Image text-base: 0x600089C0, data-base: 0x60A60000

SYSTEM INIT: INSUFFICIENT MEMORY TO BOOT THE IMAGE!

C3660 processor with 32768 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

I think I need to upgrade my memory.

4 REPLIES
Bronze

Re: Insufficient memory to boot image when adding new module for

Your memory is really low but I cant tell you if its the real problem. I've never seen it happen when adding modules. Only when upgrading. I can tell you to go to www.kingston.com for memory. We just upgraded our 3660s to 32mb flash and 160mb dram, really cheap compared to the cisco prices. They have a really good online interface that shows what the router can hold. Be carefull though because older 366x routers cannot use the high density memory chips. They have both types and exchange ours when we got the wrong ones (we have old 3660s), but you can get it clear ahead of time to avoid the issue.

Community Member

Re: Insufficient memory to boot image when adding new module for

I would want to just the cisco memory one instead of the kingston one

Cisco Employee

Re: Insufficient memory to boot image when adding new module for

Router is talking about DRAM is not sufficient so you need to add DRAM. I would say add one more 16MB module

Community Member

Re: Insufficient memory to boot image when adding new module for

Can you give me specifications or product number so that I can order it. Or a link that will be helpful

thanks

146
Views
0
Helpful
4
Replies
CreatePlease to create content