04-28-2003 08:03 PM - edited 03-02-2019 06:58 AM
Hello,
I have been trying to get my 2514 working but Im stuck. I have a 2514 connected to internet and a small lan. I can ping my outside router ip from my lan but I cant ping my outside gateway. The router is not forwarding past the outside eth0. Here is my IOS config file
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
logging queue-limit 100
no logging console
enable password ####
!
ip subnet-zero
!
partition flash 2 8 8
!
!
!
!
interface Ethernet0
ip address 66.215.146.170 255.255.255.128
ip nat outside
!
interface Ethernet1
ip address 192.168.100.1 255.255.255.0
ip nat inside
!
interface Serial0
no ip address
shutdown
!
interface Serial1
no ip address
shutdown
!
ip nat pool ovrld 66.215.146.170 66.215.146.170 prefix-length 25
ip nat inside source list 7 pool ovrld overload
ip classless
ip route 0.0.0.0 0.0.0.0 66.215.146.129
ip http server
!
access-list 7 permit 192.168.100.0 0.0.0.255
!
line con 0
line aux 0
line vty 0 4
password ####
login
!
end
04-28-2003 11:05 PM
Cau u ping your 66.215.146.129 from your router?
I think 66.215.146.129 maybe down.
04-29-2003 05:58 AM
No I can not ping my gateway from my router. I can ping eth0 (66.215.146.170) and I have tested that I can access the internet by bypassing the router and configuring a computer directly. Does my config look correct?
04-29-2003 06:34 AM
HI
You are in the wrong way. If you use one IP address for translating to Global Outside , you dont need to have a Pool ip addresses and you should type this and be trusted that this is worked.
ip nat inside source list 7 interface eth0 overload
!
access-list 7 permit ip 192.168.100.0 0.0.0.255
NIX Technologies
Mohsen(Ir).
04-29-2003 07:23 AM
Ok, I have change the nat pool as you said but I still can ping my routers gateway. Here is my modified IOS config
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
logging queue-limit 100
no logging console
enable password 6314
!
ip subnet-zero
!
partition flash 2 8 8
!
!
!
!
interface Ethernet0
ip address 66.215.146.170 255.255.255.128
ip nat outside
!
interface Ethernet1
ip address 192.168.100.1 255.255.255.0
ip nat inside
!
interface Serial0
no ip address
shutdown
!
interface Serial1
no ip address
shutdown
!
ip nat inside source list 7 interface Ethernet0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 66.215.146.129
ip http server
!
access-list 7 permit 192.168.100.0 0.0.0.255
!
line con 0
line aux 0
line vty 0 4
password neutec
login
!
end
thanks for you help and time
04-28-2003 11:19 PM
Hi Jay,
Make sure you do not connect the two ethernets port into one Cisco Catayst Switch. If you do so, please verify tha the SPT from the switch is disable (sometimes the SPT block one port - but make sure again there are no loop in your network when you disable SPT feature).
Best Regards,
HATO
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide