Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

IOS XRv VM not booting

I am trying to setup a lab with XRv VMs. I downloaded the VMDK files, setup a dedicated ubuntu 12.04 server with KVM installed and followed the installation guide.

When I boot the VM it starts the boot process until it gets to the following error messages:

Jul 31 07:39:00.127: Install Setup: Booting with committed software
Jul 31 07:39:00.137: Install Setup: Install Setup (pid 237601) has failed to prepare this node successfully and will now exit: (2952434198) 'Subsystem(8181)' detected the 'fatal' condition 'Code(9)': Invalid argument
PID 237601: _dl_abort. libdscapi.dll:dllmgr: Dll not in proper format libdscapi.dll [/pkg/lib/libdscapi.dll] err_str [No such file or directory]

after a few minutes of  wait there is a crash dump:

Writing crashinfo
Exception at 0x809244f signal 5 c=2 f=0

Active process(s):

                 CR0 #         0x8004003b
                 CR2 #          0x40d7ffc
                 CR3 #          0xfea9fc0
                 CR4 #              0x2f0
                 DR0 #                  0
                 DR1 #                  0
                 DR2 #                  0
                 DR3 #                  0
                 DR6 #         0xffff0ff0
                 DR7 #              0x400

          GDTR limit #              0x13f
   GDTR base address #         0xfed1849c
                LDTR #               0xa0
          IDTR limit #              0x70f
   IDTR base address #         0xfed165dc
                  TR #              0x100
Dumping kernel printf messages

Writing crashinfo done!

Writing x86 kernel core file
ENTER get_kernel_end
Getting kernel end success: 0xad3000 rc = 0
Heap start = 0xe0000000 Heap End = 0xfe400000Checking heap num_seg = 0
Total number of segments found  22
Writing heap elf header
Done writing heap elf headers
compress failed
ERROR dumping ker_text_data

Writing kernel core file failed

       REGISTER INFO
       EDI       ESI       EBP       EXX
  R0   28000007  1000c0b8  040faf94  fe3dccd0
       EBX       EDX       ECX       EAX
  R4   00000000  0819c445  080cff40  08195e1e
       EIP        CS       EFL       ESP
  R8   0809244f  000000f3  00001216  040faf30
       SS
  R12  000000fb

              Control Registers
                 CR0 #         0x8004003b
                 CR0 #         0x8004003b
                 CR2 #          0x40d7ffc
                 CR2 #          0x40d7ffc
                 CR3 #          0xfea9fc0
                 CR3 #          0xfea9fc0
                 CR4 #              0x2f0
                 CR4 #              0x2f0

              Debug Registers
                 DR0 #                  0
                 DR0 #                  0
                 DR1 #                  0
                 DR1 #                  0
                 DR2 #                  0
                 DR2 #                  0
                 DR3 #                  0
                 DR3 #                  0
                 DR6 #         0xffff0ff0
                 DR6 #         0xffff0ff0
                 DR7 #              0x400

                 DR7 #              0x400

          GDTR limit #              0x13f

          GDTR limit #              0x13f
   GDTR base address #         0xfed1849c
   GDTR base address #         0xfed1849c
                LDTR #               0xa0
                LDTR #               0xa0
          IDTR limit #              0x70f
          IDTR limit #              0x70f
   IDTR base address #         0xfed165dc
   IDTR base address #         0xfed165dc
                  TR #              0x100
                  TR #              0x100

 STACK TRACE
#0 0x0
Calling platform_kd_reboot ...

and the VM reboots. What am I doing wrong?

350
Views
0
Helpful
0
Replies
CreatePlease to create content