Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

IPService License for Cisco 3750

Good Day

Can anyone assist me on IPService License for Cisco 3750 to enable full ip routing

Below find details :

NAMDRPHOST#sh license detail

Index: 1        Feature: ipbase                            Version: 1.0

        License Type: Permanent

        License State: Active, In Use

        License Priority: Medium

        License Count: Non-Counted

        Store Index: 0

        Store Name: Primary License Storage

 

Index: 2        Feature: ipservices                        Version: 1.0

        License Type: Evaluation

        License State: Active, Not in Use, EULA not accepted

            Evaluation total period: 8  weeks 4  days

            Evaluation period left: 8  weeks 4  days

        License Priority: None

        License Count: Non-Counted

        Store Index: 0

        Store Name: Evaluation License Storage

 

 

NAMDRPHOST#sh ver

Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE5, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Thu 09-Feb-12 18:14 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x02800000

 

ROM: Bootstrap program is C3750E boot loader

BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)

 

NAMDRPHOST uptime is 1 day, 4 hours, 47 minutes

System returned to ROM by power-on

System restarted at 07:02:44 sa Sun Oct 9 2016

System image file is "flash:/c3750e-universalk9-mz.122-55.SE5/c3750e-universalk9-mz.122-55.SE5.bin"

 

1 REPLY
VIP Purple

Hi

Hi

did you purchase the ipservices license or are you just trying to enable the evaluation ....4

Usage Guidelines

Use the license boot level command for these purposes:

  • Downgrade or upgrade licenses
  • Enable or disable an evaluation or extension license
  • Clear an upgrade license

This command forces the licensing infrastructure to boot the configured license level instead of the license hierarchy maintained by the licensing infrastructure for a given module.

  • When the switch reloads, the licensing infrastructure checks the configuration in the startup configuration for any licenses. If there is a license in the configuration, the switch boots with that license. If there is no license, the licensing infrastructure follows the image hierarchy to check for licenses.
  • If the forced boot evaluation license expires, the licensing infrastructure follows the regular hierarchy to check for licenses.
  • If the configured boot license is already expired, the licensing infrastructure follows the hierarchy to check for licenses.

This command takes effect at the next reboot of any of the supervisors (Act or stby). This configuration must be saved to the startup configuration for it to be effective. After you configure the level, the next time the standby supervisor boots up, this configuration is applied to it.

To boot the standby supervisor to a different level than active, configure that level by using this command and then bring up the standby.

If the show license all command displays the license as "Active, Not in Use, EULA not accepted," you can use the license boot level command to enable the license and accept the end-user license agreement (EULA).

Examples

The following example shows how to activate the ipbase license on the switch upon the next reload:

Switch(config)# license boot level ipbase

Related Commands

Command

Description

license install

Installs a stored license file.

license save

Saves a copy of a permanent license to a specified license file.

show license all

Shows information about all licenses in the system.

80
Views
0
Helpful
1
Replies