07-19-2002 11:39 PM - edited 03-02-2019 12:02 AM
Dear Friends.
I m enclosing the log files. The ISDN is not coming up.I have checked the ISDN the line is not having any probs. But if i reset the port the ISDN is coming up for 1 minute or so. kindly give me the suggestion for it
dialer map ip 10.253.150.213 name bclsurat broadcast 02613229873
dialer-group 2
isdn switch-type basic-net3
!
interface BRI1/3
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
demo#
demo#
demo#
demo#wr
Building configuration...
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![OK]
demo#sh run
Building configuration...
Current configuration : 1990 bytes
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname demo
!
enable secret 5 $1$j58Y$0ZlK4OWwtBPJ/MtPp5ETt.
enable password airtel
!
!
!
!
!
memory-size iomem 25
ip subnet-zero
no ip domain-lookup
!
isdn switch-type basic-net3
!
!
!
interface Tunnel0
ip address 10.10.100.29 255.255.255.252
tunnel source BRI1/0
tunnel destination 202.56.253.182
!
interface Ethernet0/0
ip address 10.80.2.12 255.255.255.0
no ip mroute-cache
!
interface Serial0/0
no ip address
no ip mroute-cache
shutdown
!
interface Ethernet0/1
no ip address
no ip mroute-cache
shutdown
!
interface Serial0/1
no ip address
no ip mroute-cache
shutdown
!
interface BRI1/0
no ip address
encapsulation ppp
dialer idle-timeout 658230
dialer string 6405352
dialer-group 2
isdn switch-type basic-net3
ppp authentication chap
ppp pap sent-username testahm password 7 0835495D1D180D1A
!
interface BRI1/1
ip address negotiated
dialer-group 1
isdn switch-type basic-net3
!
interface BRI1/2
ip address 10.253.150.214 255.255.255.252
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer idle-timeout 300
dialer map ip 10.253.150.213 name bclsurat broadcast 02613229873
dialer-group 2
isdn switch-type basic-net3
!
interface BRI1/3
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
interface BRI1/4
no ip address
no ip mroute-cache
isdn switch-type basic-net3
!
interface BRI1/5
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
interface BRI1/6
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
interface BRI1/7
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
ip classless
ip route 10.201.24.0 255.255.255.0 Tunnel0
ip route 192.0.0.0 255.0.0.0 10.80.2.1
ip route 192.168.1.0 255.255.255.0 Tunnel0
no ip http server
!
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
demo#debug isdn eve
demo#debug isdn events
ISDN events debugging is on
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
00:21:32: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:34: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:36: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:38: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:40: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
Success rate is 0 percent (0/5)
demo#conf t
Enter configuration commands, one per line. End with CNTL/Z.
demo(config)#int bri1/2
demo(config-if)#shut
demo(config-if)#
00:22:29: ISDN BR1/2 EVENT: State = 6, Old State = 4
00:22:29: %LINK-5-CHANGED: Interface BRI1/2, changed state to administratively d
own
00:22:29: ISDN BR1/2 EVENT: State = 6, Old State = 4no
00:22:29: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:29: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to downshut
00:22:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/2, changed state
to down
demo(config-if)#
00:22:32: ISDN BR1/2 EVENT: State = 0, Old State = 6
00:22:32: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:32: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to down
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:22:32: %LINK-3-UPDOWN: Interface BRI1/2, changed state to up
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:22:32: ISDN BR1/2: L1 is IF_ACTIVE
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 4
00:22:32: ISDN BR1/2: Incoming call id = 0x0005, dsl 10
00:22:137438953472: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/2, TEI 96 change
d to up
demo(config-if)#
demo(config-if)#
demo(config-if)#
demo(config-if)#^Z
demo#ping 10.253.150.213
00:22:40: %SYS-5-CONFIG_I: Configured fromsh run
Building configuration...
Current configuration : 1990 bytes
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname demo
!
enable secret 5 $1$j58Y$0ZlK4OWwtBPJ/MtPp5ETt.
enable password airtel
!
!
!
!
!
memory-size iomem 25
ip subnet-zero
no ip domain-lookup
!
isdn switch-type basic-net3
!
!
!
interface Tunnel0
--More--
00:22:180388626432: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 96 chan
ged to down
00:22:188978561023: ISDN BR1/2: Incoming call id = 0x0006, dsl 10
00:22:186840552325: ISDN BR1/2: received HOST_INCOMING_CALL call_id 0x6
00:22:184683593728: ISDN BR1/2: HOST_INCOMING_CALL: (non-POTS) DATA
00:22:184683593728: ISDN BR1/2: HOST_INCOMING_CALL: (1) call_type = DATA
00:22:184683593728: ISDN BR1/2: HOST_INCOMING_CALL: voice_answer_data = FALSE ca
ll type is DATA
00:22:184683594411: ISDN BR1/2: RM returned call_type 0 resource type 0 response
1
00:22:43: ISDN BR1/2: isdn_send_connect(): msg 4, call id 0x6, ces 1 bchan 0, ca
ll type DATA
00:22:43: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to up
00:22:188978561024: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/2, TEI 96 change
d to up
00:22:188978561024: ISDN BR1/2: received HOST_CONNECT call_id 0x6
00:22:188978561024: ISDN BR1/2: Event: Connected o
demo#wn> on B1 at 64 Kb/s
00:22:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/2:1, changed stat
e to up
00:22:208317550516: ISDN BR1/2: received HOST_DISCONNECT call_id 0x6
00:22:206158430208: ISDN BR1/2: Event: Call to <unknown> was hung up.
00:22:208317550388: ISDN BR1/2: process_disc_ack(): call id 0x6, ces 1, call typ
e DATA
00:22:207017750578: %ISDN-6-DISCONNECT: Interface BRI1/2:1 disconnected from un
known , call lasted 4 seconds
00:22:208315397932: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:208315388805: ISDN BR1/2: received HOST_DISCONNECT_ACK call_id 0x6
00:22:206158430208: ISDN BR1/2: HOST_DISCONNECT_ACK: call type is DATA
00:22:49: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/2:1, changed stat
e to down
demo#
demo#
demo#
demo#conf t
00:22:231928233984: ISDN BR1/2: Incoming call id = 0x0007, dsl 10
00:22:234087354292: ISDN BR1/2: received HOST_INCOMING_CALL call_id 0x7
00:22:231928233984: ISDN BR1/2: HOST_INCOMING_CALL: (non-POTS) DATA
00:22:231928233984: ISDN BR1/2: HOST_INCOMING_CALL: (1) call_type = DATA
00:22:231928233984: ISDN BR1/2: HOST_INCOMING_CALL: voice_answer_data = FALSE ca
ll type is DATA
00:22:231928234667: ISDN BR1/2: RM returned call_type 0 resource type 0 response
1
00:22:54: ISDN BR1/2: isdn_send_connect(): msg 4, call id 0x7, ces 1 bchan 0, ca
ll type DATA
00:22:54: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to up
00:22:231928233984: ISDN BR1/2: received HOST_CONNECT call_id 0x7
00:22:231928233984: ISDN BR1/2: Event: Connected to <unknown> on B1 at 64 Kb/s
Enter configuration commands, one per line. End with CNTL/Z.
demo(config)#
demo(config)#
demo(config)#
demo(config)#
demo(config)#
00:22:251267223476: ISDN BR1/2: received HOST_DISCONNECT call_id 0x7
00:22:249108103168: ISDN BR1/2: Event: Call to <unknown> was hung up.
00:22:251267223348: ISDN BR1/2: process_disc_ack(): call id 0x7, ces 1, call typ
e DATA
00:22:249950188850: %ISDN-6-DISCONNECT: Interface BRI1/2:1 disconnected from un
known , call lasted 4 seconds
00:22:251265070892: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:251265061765: ISDN BR1/2: received HOST_DISCONNECT_ACK call_id 0x7
00:22:249108103168: ISDN BR1/2: HOST_DISCONNECT_ACK: call type is DATA
demo(config)#
demo(config)#
demo(config)#
demo(config)#
demo(config)#
demo(config)#^Z
demo#
demo#
demo#
demo#s d
00:23:03: %SYS-5-CONFIG_I: Configured from console by consoleialer
BRI1/0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
6405352 0 4 00:21:58 failed Default
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/0:1 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/0:2 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
--More--
00:23:34359738368: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 96 chang
e n
BRI1/1:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
02613229873 0 0 never -
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/2:1 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2:2 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/3 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/3:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is shutdown
demo#s dialer
BRI1/0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
6405352 0 4 00:22:08 failed Default
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/0:1 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/0:2 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/1:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
02613229873 0 0 never -
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
--More--
00:23:21: ISDN BR1/2 EVENT: State = 4, Old State = 4
00:23:21: ISDN BR1/2 EVENT: State = 0, Old State = 4
00:23:21: ISDN BR1/2: Physical layer is IF_DOWN
00:23:91117060095: ISDN BR1/2: Shutting down ME
00:23:90194313216: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI1/2, TEI 96 chan
ged to down
00:23:90194313216: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 96 chang
ed to down
00:23:94489280511: ISDN BR1/2: Shutting down ISDN Layer 3
00:23:92353401284: L3: L3_GetUser_NLCB failed, message ignored cid 0x0 cr 0x0 ev
0x211 ceBRI1/2:1 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2:2 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/3 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/3:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is shutdown
BRI1/3:2 - dialer type = ISDN
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
00:23:32: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:34: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:36: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:38: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:40: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
Success rate is 0 percent (0/5)
demo#conf t
Enter configuration commands, one per line. End with CNTL/Z.
demo(config)#int bri1/2
demo(config-if)#shut
demo(config-if)#
00:23:49: ISDN BR1/2 EVENT: State = 6, Old State = 4
00:23:49: %LINK-5-CHANGED: Interface BRI1/2, changed state to administratively d
own
00:23:49: ISDN BR1/2 EVENT: State = 6, Old State = 4
00:23:49: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:23:49: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to down
demo(config-if)#
demo(config-if)#
demo(config-if)#
demo(config-if)#
demo(config-if)#no shut
demo(config-if)#
00:23:53: ISDN BR1/2 EVENT: State = 0, Old State = 6
00:23:53: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:23:53: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to down
00:23:53: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:23:53: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:23:53: %LINK-3-UPDOWN: Interface BRI1/2, changed state to up^Z
demo#
00:23:53: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:23:54: ISDN BR1/2: L1 is IF_ACTIVE
00:23:54: ISDN BR1/2 EVENT: State = 4, Old State = 4
00:23:54: ISDN BR1/2: Incoming call id = 0x0008, dsl 10
00:23:234087329924: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/2, TEI 65 change
d to up
00:23:54: %SYS-5-CONFIG_I: Configured from console by console
demo#
demo#
demo#
demo#sh isdn
00:24:17179869184: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 65 chang
ed to down st
Global ISDN Switchtype = basic-net3
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 8 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 9
ISDN BRI1/1 interface
dsl 9, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 9 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 0
ISDN BRI1/2 interface
dsl 10, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 65, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
I_Queue_Len 0, UI_Queue_Len 0
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 10 CCBs = 0
The Free Channel Mask: 0x3
Number of L2 Discards = 0, L2 Session ID = 10
ISDN BRI1/3 interface
dsl 11, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 11 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 0
ISDN BRI1/4 interface
dsl 12, interface ISDN Switchtype = basic-net3
Layer 1 Status:
demo#
dialer map ip 10.253.150.213 name bclsurat broadcast 02613229873
dialer-group 2
isdn switch-type basic-net3
!
interface BRI1/3
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
demo#
demo#
demo#
demo#wr
Building configuration...
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![OK]
demo#sh run
Building configuration...
Current configuration : 1990 bytes
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname demo
!
enable secret 5 $1$j58Y$0ZlK4OWwtBPJ/MtPp5ETt.
enable password airtel
!
!
!
!
!
memory-size iomem 25
ip subnet-zero
no ip domain-lookup
!
isdn switch-type basic-net3
!
!
!
interface Tunnel0
ip address 10.10.100.29 255.255.255.252
tunnel source BRI1/0
tunnel destination 202.56.253.182
!
interface Ethernet0/0
ip address 10.80.2.12 255.255.255.0
no ip mroute-cache
!
interface Serial0/0
no ip address
no ip mroute-cache
shutdown
!
interface Ethernet0/1
no ip address
no ip mroute-cache
shutdown
!
interface Serial0/1
no ip address
no ip mroute-cache
shutdown
!
interface BRI1/0
no ip address
encapsulation ppp
dialer idle-timeout 658230
dialer string 6405352
dialer-group 2
isdn switch-type basic-net3
ppp authentication chap
ppp pap sent-username testahm password 7 0835495D1D180D1A
!
interface BRI1/1
ip address negotiated
dialer-group 1
isdn switch-type basic-net3
!
interface BRI1/2
ip address 10.253.150.214 255.255.255.252
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer idle-timeout 300
dialer map ip 10.253.150.213 name bclsurat broadcast 02613229873
dialer-group 2
isdn switch-type basic-net3
!
interface BRI1/3
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
interface BRI1/4
no ip address
no ip mroute-cache
isdn switch-type basic-net3
!
interface BRI1/5
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
interface BRI1/6
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
interface BRI1/7
no ip address
no ip mroute-cache
shutdown
isdn switch-type basic-net3
!
ip classless
ip route 10.201.24.0 255.255.255.0 Tunnel0
ip route 192.0.0.0 255.0.0.0 10.80.2.1
ip route 192.168.1.0 255.255.255.0 Tunnel0
no ip http server
!
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
demo#debug isdn eve
demo#debug isdn events
ISDN events debugging is on
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
00:21:32: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:34: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:36: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:38: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:21:40: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
Success rate is 0 percent (0/5)
demo#conf t
Enter configuration commands, one per line. End with CNTL/Z.
demo(config)#int bri1/2
demo(config-if)#shut
demo(config-if)#
00:22:29: ISDN BR1/2 EVENT: State = 6, Old State = 4
00:22:29: %LINK-5-CHANGED: Interface BRI1/2, changed state to administratively d
own
00:22:29: ISDN BR1/2 EVENT: State = 6, Old State = 4no
00:22:29: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:29: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to downshut
00:22:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/2, changed state
to down
demo(config-if)#
00:22:32: ISDN BR1/2 EVENT: State = 0, Old State = 6
00:22:32: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:32: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to down
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:22:32: %LINK-3-UPDOWN: Interface BRI1/2, changed state to up
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:22:32: ISDN BR1/2: L1 is IF_ACTIVE
00:22:32: ISDN BR1/2 EVENT: State = 4, Old State = 4
00:22:32: ISDN BR1/2: Incoming call id = 0x0005, dsl 10
00:22:137438953472: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/2, TEI 96 change
d to up
demo(config-if)#
demo(config-if)#
demo(config-if)#
demo(config-if)#^Z
demo#ping 10.253.150.213
00:22:40: %SYS-5-CONFIG_I: Configured fromsh run
Building configuration...
Current configuration : 1990 bytes
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname demo
!
enable secret 5 $1$j58Y$0ZlK4OWwtBPJ/MtPp5ETt.
enable password airtel
!
!
!
!
!
memory-size iomem 25
ip subnet-zero
no ip domain-lookup
!
isdn switch-type basic-net3
!
!
!
interface Tunnel0
--More--
00:22:180388626432: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 96 chan
ged to down
00:22:188978561023: ISDN BR1/2: Incoming call id = 0x0006, dsl 10
00:22:186840552325: ISDN BR1/2: received HOST_INCOMING_CALL call_id 0x6
00:22:184683593728: ISDN BR1/2: HOST_INCOMING_CALL: (non-POTS) DATA
00:22:184683593728: ISDN BR1/2: HOST_INCOMING_CALL: (1) call_type = DATA
00:22:184683593728: ISDN BR1/2: HOST_INCOMING_CALL: voice_answer_data = FALSE ca
ll type is DATA
00:22:184683594411: ISDN BR1/2: RM returned call_type 0 resource type 0 response
1
00:22:43: ISDN BR1/2: isdn_send_connect(): msg 4, call id 0x6, ces 1 bchan 0, ca
ll type DATA
00:22:43: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to up
00:22:188978561024: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/2, TEI 96 change
d to up
00:22:188978561024: ISDN BR1/2: received HOST_CONNECT call_id 0x6
00:22:188978561024: ISDN BR1/2: Event: Connected o
demo#wn> on B1 at 64 Kb/s
00:22:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/2:1, changed stat
e to up
00:22:208317550516: ISDN BR1/2: received HOST_DISCONNECT call_id 0x6
00:22:206158430208: ISDN BR1/2: Event: Call to <unknown> was hung up.
00:22:208317550388: ISDN BR1/2: process_disc_ack(): call id 0x6, ces 1, call typ
e DATA
00:22:207017750578: %ISDN-6-DISCONNECT: Interface BRI1/2:1 disconnected from un
known , call lasted 4 seconds
00:22:208315397932: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:208315388805: ISDN BR1/2: received HOST_DISCONNECT_ACK call_id 0x6
00:22:206158430208: ISDN BR1/2: HOST_DISCONNECT_ACK: call type is DATA
00:22:49: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/2:1, changed stat
e to down
demo#
demo#
demo#
demo#conf t
00:22:231928233984: ISDN BR1/2: Incoming call id = 0x0007, dsl 10
00:22:234087354292: ISDN BR1/2: received HOST_INCOMING_CALL call_id 0x7
00:22:231928233984: ISDN BR1/2: HOST_INCOMING_CALL: (non-POTS) DATA
00:22:231928233984: ISDN BR1/2: HOST_INCOMING_CALL: (1) call_type = DATA
00:22:231928233984: ISDN BR1/2: HOST_INCOMING_CALL: voice_answer_data = FALSE ca
ll type is DATA
00:22:231928234667: ISDN BR1/2: RM returned call_type 0 resource type 0 response
1
00:22:54: ISDN BR1/2: isdn_send_connect(): msg 4, call id 0x7, ces 1 bchan 0, ca
ll type DATA
00:22:54: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to up
00:22:231928233984: ISDN BR1/2: received HOST_CONNECT call_id 0x7
00:22:231928233984: ISDN BR1/2: Event: Connected to <unknown> on B1 at 64 Kb/s
Enter configuration commands, one per line. End with CNTL/Z.
demo(config)#
demo(config)#
demo(config)#
demo(config)#
demo(config)#
00:22:251267223476: ISDN BR1/2: received HOST_DISCONNECT call_id 0x7
00:22:249108103168: ISDN BR1/2: Event: Call to <unknown> was hung up.
00:22:251267223348: ISDN BR1/2: process_disc_ack(): call id 0x7, ces 1, call typ
e DATA
00:22:249950188850: %ISDN-6-DISCONNECT: Interface BRI1/2:1 disconnected from un
known , call lasted 4 seconds
00:22:251265070892: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:22:251265061765: ISDN BR1/2: received HOST_DISCONNECT_ACK call_id 0x7
00:22:249108103168: ISDN BR1/2: HOST_DISCONNECT_ACK: call type is DATA
demo(config)#
demo(config)#
demo(config)#
demo(config)#
demo(config)#
demo(config)#^Z
demo#
demo#
demo#
demo#s d
00:23:03: %SYS-5-CONFIG_I: Configured from console by consoleialer
BRI1/0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
6405352 0 4 00:21:58 failed Default
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/0:1 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/0:2 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
--More--
00:23:34359738368: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 96 chang
e n
BRI1/1:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
02613229873 0 0 never -
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/2:1 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2:2 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/3 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/3:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is shutdown
demo#s dialer
BRI1/0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
6405352 0 4 00:22:08 failed Default
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/0:1 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/0:2 - dialer type = ISDN
Idle timer (658230 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/1:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/1:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
02613229873 0 0 never -
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
--More--
00:23:21: ISDN BR1/2 EVENT: State = 4, Old State = 4
00:23:21: ISDN BR1/2 EVENT: State = 0, Old State = 4
00:23:21: ISDN BR1/2: Physical layer is IF_DOWN
00:23:91117060095: ISDN BR1/2: Shutting down ME
00:23:90194313216: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI1/2, TEI 96 chan
ged to down
00:23:90194313216: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 96 chang
ed to down
00:23:94489280511: ISDN BR1/2: Shutting down ISDN Layer 3
00:23:92353401284: L3: L3_GetUser_NLCB failed, message ignored cid 0x0 cr 0x0 ev
0x211 ceBRI1/2:1 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/2:2 - dialer type = ISDN
Idle timer (300 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI1/3 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI1/3:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is shutdown
BRI1/3:2 - dialer type = ISDN
demo#ping 10.253.150.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.253.150.213, timeout is 2 seconds:
00:23:32: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:34: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:36: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:38: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
00:23:40: ISDN BRI1/2: isdn_is_bchannel_available: No Free B-channels.
Success rate is 0 percent (0/5)
demo#conf t
Enter configuration commands, one per line. End with CNTL/Z.
demo(config)#int bri1/2
demo(config-if)#shut
demo(config-if)#
00:23:49: ISDN BR1/2 EVENT: State = 6, Old State = 4
00:23:49: %LINK-5-CHANGED: Interface BRI1/2, changed state to administratively d
own
00:23:49: ISDN BR1/2 EVENT: State = 6, Old State = 4
00:23:49: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:23:49: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to down
demo(config-if)#
demo(config-if)#
demo(config-if)#
demo(config-if)#
demo(config-if)#no shut
demo(config-if)#
00:23:53: ISDN BR1/2 EVENT: State = 0, Old State = 6
00:23:53: %LINK-3-UPDOWN: Interface BRI1/2:1, changed state to down
00:23:53: %LINK-3-UPDOWN: Interface BRI1/2:2, changed state to down
00:23:53: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:23:53: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:23:53: %LINK-3-UPDOWN: Interface BRI1/2, changed state to up^Z
demo#
00:23:53: ISDN BR1/2 EVENT: State = 4, Old State = 6
00:23:54: ISDN BR1/2: L1 is IF_ACTIVE
00:23:54: ISDN BR1/2 EVENT: State = 4, Old State = 4
00:23:54: ISDN BR1/2: Incoming call id = 0x0008, dsl 10
00:23:234087329924: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/2, TEI 65 change
d to up
00:23:54: %SYS-5-CONFIG_I: Configured from console by console
demo#
demo#
demo#
demo#sh isdn
00:24:17179869184: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/2, TEI 65 chang
ed to down st
Global ISDN Switchtype = basic-net3
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 8 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 9
ISDN BRI1/1 interface
dsl 9, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 9 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 0
ISDN BRI1/2 interface
dsl 10, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 65, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
I_Queue_Len 0, UI_Queue_Len 0
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 10 CCBs = 0
The Free Channel Mask: 0x3
Number of L2 Discards = 0, L2 Session ID = 10
ISDN BRI1/3 interface
dsl 11, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 11 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 0
ISDN BRI1/4 interface
dsl 12, interface ISDN Switchtype = basic-net3
Layer 1 Status:
demo#
demo#
demo#s ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.1(10a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Mon 04-Feb-02 09:47 by kellythw
Image text-base: 0x80008088, data-base: 0x80816698
ROM: System Bootstrap, Version 12.2(6r), RELEASE SOFTWARE (fc1)
demo uptime is 23 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.121-10a.bin"
cisco 2611 (MPC860) processor (revision 0x00) with 24576K/8192K bytes of memory.
Processor board ID JAD061008FJ (154101789)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
8 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
regards
Manish Shamjee
07-20-2002 03:25 AM
Hi Manish,
This has to do with ISDN Layer 3. Give the command "debug isdn q931" and check the cause for disconnection from the link "cause i = 0x ". Then go to the following link and check the disconnection cause.
http://www.cisco.com/warp/public/471/isdn_q931_ts.html
Most of the times the problem will be at exchange end. They usually do the test using ISDN phone. But this doesnt mean that the data is through. They have to do some settings on the ISDN switch to enable data.
Hope this will help
regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide