Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

ISDN Problem

Hi,

Anyone got any idea what this means?

CCB:callid=80F1, sapi=0, ces=0, B-chan=31, calltype=DATA, hdlctype=HDLC-TRUNK

I have configured ISDN and seem to be getting the above on my layer 3. For ref please see the output from various commands.

# sh isdn status

Global ISDN Switchtype = primary-net5

ISDN Serial1/0:15 interface

dsl 0, interface ISDN Switchtype = primary-net5

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

Layer 3 Status:

0 Active Layer 3 Call(s)

CCB:callid=80F1, sapi=0, ces=0, B-chan=31, calltype=DATA, hdlctype=HDLC-TRUNK

Active dsl 0 CCBs = 1

The Free Channel Mask: 0xBFFF7FFF

Number of L2 Discards = 0, L2 Session ID = 2

Total Allocated ISDN CCBs = 1

sh run

Building configuration...

Current configuration : 3922 bytes

controller E1 1/0

framing NO-CRC4

pri-group timeslots 1-31

!

interface Serial1/0:15

description local ISDN number tba

no ip address

ip access-group 143 in

encapsulation ppp

dialer pool-member 1

isdn switch-type primary-net5

no cdp enable

ppp authentication chap

!

interface Dialer1

ip address x.x.x.x x.x.x.x

ip access-group 143 in

encapsulation ppp

dialer pool 1

dialer remote-name xxxxxxxx

dialer string xxxxxxxx

dialer load-threshold 128 outbound

dialer watch-group 1

dialer-group 1

no cdp enable

ppp authentication chap

ppp chap hostname xxxxxxxxx

ppp multilink

++++++++++++++++++++++

sh int s1/0:15

Serial1/0:15 is up, line protocol is up (spoofing)

Hardware is DSX1

Description: local ISDN number tba

MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,

reliability 255/255, txload 19/255, rxload 7/255

Encapsulation PPP, loopback not set

Last input 00:00:00, output 00:00:00, output hang never

Last clearing of "show interface" counters 00:11:40

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 4

Queueing strategy: weighted fair

Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Conversations 0/1/256 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

Available Bandwidth 48 kilobits/sec

5 minute input rate 2000 bits/sec, 37 packets/sec

5 minute output rate 5000 bits/sec, 37 packets/sec

21791 packets input, 185161 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

21801 packets output, 392172 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

1 carrier transitions

++++++++++

sh controllers e1 1/0

E1 1/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

Data in current interval (872 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 1 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 1 Severely Err Secs, 0 Unavail Secs

+++++++++++

Any bit of information will be great help.

Thank you in advance.

Cheers

Jay

1 REPLY
Bronze

Re: ISDN Problem

As such from the show isdn status , your line is not have no problem , its explains caller Id , calltype =voice/data, encapsulation=PPP/HDLC, which channel is currehtly is used . If you are interesting to troubleshooting E1 you can use these links

http://www.cisco.com/warp/public/116/T1_pri.html

http://www.cisco.com/en/US/tech/tk713/tk628/technologies_tech_note09186a00800a70fb.shtml

http://www.cisco.com/en/US/tech/tk713/tk628/technologies_tech_note09186a00801509d7.shtml

http://www.cisco.com/warp/public/129/bri_sh_isdn_stat.html#spid

286
Views
4
Helpful
1
Replies
CreatePlease login to create content