03-07-2002 07:10 AM - edited 03-01-2019 08:47 PM
Anybody know, i may using Qsig protocol for organizing Dial-Up access to 3620 router? What need version IOS may using for this?
No found answer in documentation on CCO.
03-07-2002 09:09 AM
Hi,
12.1.(2)T & later, please refer to:
Thanks,
Mak.
03-08-2002 05:37 AM
This document help about using Qsig for VoiceIP application, no about Dial-Up. This function supported?
I configure this. No work.
See deb isdn q931
1d02h: ISDN Se1/1:15: RX <- SETUP pd = 8 callref = 0x1102
1d02h: Bearer Capability i = 0x8090A3
1d02h: Channel ID i = 0xA98381
1d02h: Progress Ind i = 0xA590 - Reserved value
1d02h: Progress Ind i = 0x8581 - Call not end-to-end ISDN, may have in-b
and info
1d02h: Called Party Number i = 0xC9, '279', Plan:Private, Type:Subscribe
r(local)
1d02h: Sending Complete
1d02h: Locking Shift to Codeset 5
1d02h: Codeset 5 IE 0x31 i = 0x81
1d02h: Codeset 5 IE 0x32 i = 0x80
1d02h: ISDN Se1/1:15: Incoming call id = 0x021E, dsl 0
1d02h: ISDN Se1/1:15: NegotiateBchan: bchan 1 intid 0 serv_st 0 chan_st
0callid
0x0000 ev 0x90 n/w? 0
1d02h: Negotiated int_id 0 bchan 0 cr=0x9102 callid=0x021E lo_chan 1 final
int_i
d/bchan 0/1 cause 0x0
1d02h: ISDN Se1/1:15: LIF_EVENT: ces/callid 1/0x21E CALL_INCOMING
1d02h: ISDN Se1/1:15: CALL_INCOMING dsl 0 bchan 0
1d02h: ISDN Se1/1:15: CALL_INCOMING: call type is VOICE ALAW, bchan = 0
1d02h: ISDN Se1/1:15: Event: Checking if call is not ISDN end to end
1d02h: ISDN Se1/1:15: Event: Received a VOICE call from
64 K
b/s
1d02h: ISDN Se1/1:15: RM returned call_type 1 resource type 0 response 1
1d02h: ISDN Se1/1:15: VOICE_ANS Event: call id 0x21E, bchan 0, ces 1
1d02h: ISDN Se1/1:15: isdn_send_connect(): msg 74, call id 0x21E, ces 0
bchan 0,
call type VOICE
1d02h: ISDN Se1/1:15: RX <- SETUP pd = 8 callref = 0x1102
1d02h: Bearer Capability i = 0x8090A3
1d02h: Channel ID i = 0xA98381
1d02h: Progress Ind i = 0xA590 - Reserved value
1d02h: Progress Ind i = 0x8581 - Call not end-to-end ISDN, may have in-b
and info
1d02h: Called Party Number i = 0xC9, '279', Plan:Private, Type:Subscribe
r(local)
1d02h: Sending Complete
1d02h: Locking Shift to Codeset 5
1d02h: Codeset 5 IE 0x31 i = 0x81
1d02h: Codeset 5 IE 0x32 i = 0x80
1d02h: ISDN Se1/1:15: RX <- RELEASE_COMP pd = 8 callref = 0x1102
1d02h: Cause i = 0x80E6 - Recovery on timer expiry
1d02h: ISDN Se1/1:15: CCPRI_ReleaseCall(): bchan 1, call id 0x21E, call type
VOICE
1d02h: CCPRI_ReleaseChan released b_dsl 0 B_Chan 1
1d02h: ISDN Se1/1:15: LIF_EVENT: ces/callid 1/0x21E CALL_DISC
1d02h: ISDN Se1/1:15: LIF_EVENT: ces/callid 1/0x21E CALL_CLEARED
1d02h: ISDN Se1/1:15: received CALL_CLEARED call_id 0x21E
Software ROM: 3600 Software (C3620-DO3S-M), Version 12.2(2)T, RELEASE SOFTWARE (fc1)
In than problem?
Thank you.
03-11-2002 12:29 PM
Only VoIP, not data (modem or ISDN data) is supported over Q.SIG.
03-11-2002 07:28 PM
Thanks all.
May be this information worthy for adding in Cisco FAQ?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: