Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

LMS Real time monitor and Catalyst 5509

Hi,

I tried to add a switch in the RTM server. I filled in the correct info (systemname, ip, snmp community RO and RW string,...). I didn't specify a switch type (autodetect). But I got an error message after pressing the 'add' button, specifying that the switch was not supported.

So I tried it again, this time specifying the exact switch type (C5509) instead of using the autodetect feature. This time the RTM server was able to connect to switch and do the necessary configuration.

When I tried to monitor the switch afterwards, I didn't receive any traffic info in the graphs.

When I take a look in the config of the switch afterward I see this:

'set snmp rmon disable'

Shouldn't RTM server enable this feature when I add a switch to the RTM server?

Could it be the version of the CatOS?

A 'show version' and a 'show config' is included.

Thanks in advance!!

Kind Regards,

Tom

---------------------show version------------------------------

C5509-Info=> (enable) sh ver

WS-C5509 Software, Version McpSW: 5.2(2) NmpSW: 5.2(2)

Copyright (c) 1995-1999 by Cisco Systems

NMP S/W compiled on Nov 23 1999, 18:13:43

MCP S/W compiled on Nov 23 1999, 18:10:08

System Bootstrap Version: 5.1(2)

Hardware Version: 1.0 Model: WS-C5509 Serial #: 067523213

Mod Port Model Serial # Versions

--- ---- ---------- --------- ----------------------------------------

1 2 WS-X5530 014586398 Hw : 3.4

Fw : 5.1(2)

Fw1: 4.4(1)

Sw : 5.2(2)

2 2 WS-X5158 006855588 Hw : 2.4

Fw : 1.3

Fw1: 3.1(2)

Sw : 12.0(4a)W5(10),

3 24 WS-X5225R 014904563 Hw : 3.3

Fw : 4.3(1)

Sw : 5.2(2)

4 24 WS-X5225R 014904639 Hw : 3.3

Fw : 4.3(1)

Sw : 5.2(2)

5 24 WS-X5225R 014903186 Hw : 3.3

Fw : 4.3(1)

Sw : 5.2(2)

6 3 WS-X5403 015880702 Hw : 1.2

Fw : 4.1(1)

Sw : 5.2(2)

8 9 WS-X5410 019505468 Hw : 1.1

Fw : 4.2(5)

Fw1: 4.2(500)

Sw : 5.1(1)

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 32640K 17447K 15193K 8192K 4899K 3293K 512K 186K 326K

Uptime is 179 days, 11 hours, 53 minutes

----------------------show config all-----------------------

begin

!

# ***** ALL (DEFAULT and NON-DEFAULT) CONFIGURATION *****

!

!

#Time: Wed Nov 13 2002, 14:22:40

!

#version 5.2(2)

!

set password xxx

set enablepass xxxx

set prompt C5509-Info=>

set length 24 default

set logout 20

set banner motd ^C^C

!

#system

set system baud 9600

set system modem disable

set system name CAT5000

set system location Computerroom

set system contact xxxxxx

!

#frame distribution method

set port channel all distribution mac both

!

#snmp

set snmp community read-only xxxx

set snmp community read-write xxxx

set snmp community read-write-all xxxx

set snmp rmon disable

set snmp trap disable module

set snmp trap disable chassis

set snmp trap disable bridge

set snmp trap disable repeater

set snmp trap disable vtp

set snmp trap disable auth

set snmp trap disable ippermit

set snmp trap disable vmps

set snmp trap disable entity

set snmp trap disable config

set snmp trap disable stpx

set snmp trap disable syslog

set snmp extendedrmon vlanmode disable

set snmp extendedrmon vlanagent disable

set snmp extendedrmon enable

set snmp trap 10.20.31.100 xxxxx

!

#tacacs+

set tacacs server 10.20.31.237 primary

set tacacs attempts 3

set tacacs directedrequest disable

set tacacs key xxxx

set tacacs timeout 5

!

#radius

set radius deadtime 0

set radius timeout 5

set radius retransmit 2

!

#kerberos

!

#authentication

set authentication login tacacs disable console

set authentication login tacacs enable telnet primary

set authentication enable tacacs disable console

set authentication enable tacacs disable telnet

set authentication login radius disable console

set authentication login radius disable telnet

set authentication enable radius disable console

set authentication enable radius disable telnet

set authentication login local enable console

set authentication login local enable telnet

set authentication enable local enable console

set authentication enable local enable telnet

set authentication login kerberos disable console

set authentication login kerberos disable telnet

set authentication enable kerberos disable console

set authentication enable kerberos disable telnet

!

#bridge

set bridge apart enable

set bridge fddicheck disable

set bridge ipx snaptoether 8023raw

set bridge ipx 8022toether 8023

set bridge ipx 8023rawtofddi snap

!

#vtp

set vtp domain xxx

set vtp mode server

set vtp passwd xxxx

set vtp v2 disable

set vtp pruning disable

set vtp pruneeligible 2-1000

clear vtp pruneeligible 1001-1005

set vlan 1 name default type ethernet mtu 1500 said 100001 state active

set vlan 2 name ZOL type ethernet mtu 1500 said 100002 state active

set vlan 3 name SAN type ethernet mtu 1500 said 100003 state active

set vlan 4 name p&c type ethernet mtu 1500 said 100004 state active

set vlan 5 name OCMW type ethernet mtu 1500 said 100005 state active

set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active

set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active bridge

0x1 stp ieee

set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active bridge 0x1

stp ieee

set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active paren

t 1005 ring 0x1 mode srb aremaxhop 0 stemaxhop 0 backupcrf off

set vlan 1 translation 1003 translation 1002

set vlan 1002 translation 1003 translation 1

set vlan 1003 translation 1 translation 1002

!

#ip

set interface sc0 1 10.254.30.242/255.255.0.0 10.254.255.255

set interface sc0 up

set interface sl0 0.0.0.0 0.0.0.0

set interface sl0 up

set arp agingtime 1200

set ip redirect enable

set ip unreachable enable

set ip fragmentation enable

set ip route 0.0.0.0/0.0.0.0 10.254.31.254

set ip alias default 0.0.0.0

!

#Command alias

!

#vmps

--More--2002 Nov 13 14:22:54 %PAGP-5-PORTTOSTP:Port 4/8 joined bridge port 4/8

set vmps server retry 3

set vmps server reconfirminterval 60

set vmps downloadmethod tftp

set vmps downloadserver 0.0.0.0 vmps-config-database.1

set vmps state disable

!

#rcp

set rcp username

!

#dns

set ip dns disable

!

#spantree

#uplinkfast groups

set spantree uplinkfast disable

#backbonefast

set spantree backbonefast disable

set spantree enable all

#vlan 1

set spantree fwddelay 15 1

set spantree hello 2 1

set spantree maxage 20 1

set spantree priority 5000 1

#vlan 2

set spantree fwddelay 15 2

set spantree hello 2 2

set spantree maxage 20 2

set spantree priority 5000 2

#vlan 3

set spantree fwddelay 15 3

set spantree hello 2 3

set spantree maxage 20 3

set spantree priority 32768 3

#vlan 4

set spantree fwddelay 15 4

set spantree hello 2 4

set spantree maxage 20 4

set spantree priority 32768 4

#vlan 5

set spantree fwddelay 15 5

set spantree hello 2 5

set spantree maxage 20 5

set spantree priority 32768 5

#vlan 1003

set spantree fwddelay 15 1003

set spantree hello 2 1003

set spantree maxage 20 1003

set spantree priority 32768 1003

set spantree portstate 1003 block 1005

set spantree portcost 1003 62

set spantree portpri 1003 4

set spantree portfast 1003 disable

#vlan 1005

set spantree fwddelay 15 1005

set spantree hello 2 1005

set spantree maxage 20 1005

set spantree priority 32768 1005

set spantree multicast-address 1005 ieee

!

#cgmp

set cgmp disable

set cgmp leave disable

!

#syslog

set logging console enable

set logging server disable

set logging level cdp 2 default

set logging level mcast 2 default

set logging level dtp 5 default

set logging level dvlan 2 default

set logging level earl 2 default

set logging level fddi 2 default

set logging level ip 2 default

set logging level pruning 2 default

set logging level snmp 2 default

set logging level spantree 2 default

set logging level sys 5 default

set logging level tac 2 default

set logging level tcp 2 default

set logging level telnet 2 default

set logging level tftp 2 default

set logging level vtp 2 default

set logging level vmps 2 default

set logging level kernel 2 default

set logging level filesys 2 default

set logging level drip 2 default

set logging level pagp 5 default

set logging level mgmt 5 default

set logging level mls 5 default

set logging level protfilt 2 default

set logging level security 2 default

set logging level radius 2 default

set logging level udld 2 default

set logging level gvrp 2 default

set logging server facility LOCAL7

!

#ntp

set ntp broadcastclient enable

set ntp broadcastdelay 3000

set ntp client enable

set ntp authentication disable

set ntp server 10.20.31.63

clear timezone

set summertime disable

!

#set boot command

set boot config-register 0x2

set boot system flash bootflash:cat5000-sup3_5-2-2.bin

!

#permit list

set ip permit disable

!

#drip

set tokenring reduction enable

set tokenring distrib-crf disable

!

#igmp

set igmp disable

set igmp fastleave disable

!

#protocolfilter

set protocolfilter disable

!

#mls

set mls disable

set mls disable ipx

set mls flow destination

set mls agingtime 256

set mls agingtime ipx 256

set mls agingtime fast 0 0

set mls nde disable

!

#standby ports

set standbyports disable

!

#vlan mapping

!

#gmrp

set gmrp disable

!

#garp

set garp timer join 200

set garp timer leave 600

set garp timer leaveall 10000

!

#CDP

set cdp interval 60

set cdp holdtime 180

set cdp enable

!

#qos

set qos disable

set qos map 1q4t 1 1 cos 0

set qos map 1q4t 1 1 cos 1

set qos map 1q4t 1 2 cos 2

set qos map 1q4t 1 2 cos 3

set qos map 1q4t 1 3 cos 4

set qos map 1q4t 1 3 cos 5

set qos map 1q4t 1 4 cos 6

set qos map 1q4t 1 4 cos 7

set qos wred-threshold 1q4t tx queue 1 10 20 40 100

!

#mls multicast

set mls multicast disable

!

#UDLD

set udld disable

!

#Port Channel

set port channel 4/3-4 31

set port channel 4/5-8 32

set port channel 4/9-12 33

set port channel 4/13-16 34

set port channel 4/17-20 35

set port channel 4/21-24 36

set port channel 5/1-4 37

set port channel 5/5-8 38

set port channel 5/9-12 39

set port channel 5/13-16 40

set port channel 5/17-20 41

set port channel 5/21-24 42

set port channel 1/1 44

set port channel 1/2 45

set port channel 3/1-4 46

set port channel 3/5-8 47

set port channel 3/9-12 48

set port channel 3/13-16 49

set port channel 3/17-20 50

set port channel 3/21-24 51

set port channel 4/1-2 88

set port channel 8/1-4 89

set port channel 8/5-8 90

set port channel 8/9 91

!

#module 1 : 2-port 100BaseFX MMF Supervisor

set module name 1

set vlan 1 1/1-2

set port enable 1/1-2

set port level 1/1-2 normal

set port duplex 1/1-2 full

set port trap 1/1-2 disable

set port name 1/1-2

set port security 1/1-2 disable

set port security 1/1-2 maximum 1

set port security 1/1-2 violation shutdown

set port security 1/1-2 age 0

set port security 1/1-2 shutdown 0

set port broadcast 1/1-2 100%

set port membership 1/1-2 static

set port protocol 1/1-2 ip on

set port protocol 1/1-2 ipx auto

set port protocol 1/1-2 group auto

set cdp enable 1/1-2

set udld enable 1/1-2

set trunk 1/1 on isl 1-1005

set trunk 1/2 on isl 1-1005

set spantree portfast 1/1-2 disable

set spantree portcost 1/1-2 19

set spantree portpri 1/1-2 32

set spantree portvlanpri 1/1 0

set spantree portvlanpri 1/2 0

set spantree portvlancost 1/1 cost 18

set spantree portvlancost 1/2 cost 18

set port gmrp 1/1-2 enable

set gmrp registration normal 1/1-2

set gmrp fwdall disable 1/1-2

set port channel 1/1-2 mode off

!

#module 2 : 2-port MM OC-3 Dual-Phy ATM

set module name 2

set port level 2/1 normal

set port name 2/1-2

set cdp enable 2/1

set trunk 2/1 on lane 1-1005

set spantree portcost 2/1 14

set spantree portpri 2/1 32

set spantree portvlanpri 2/1 0

set spantree portvlancost 2/1 cost 13

set port gmrp 2/1 enable

set gmrp registration normal 2/1

set gmrp fwdall disable 2/1

!

#module 3 : 24-port 10/100BaseTX Ethernet

set module name 3

set module enable 3

set vlan 2 3/1-20,3/22-24

set vlan 5 3/21

set port enable 3/1-24

set port level 3/1-24 normal

set port speed 3/1 auto

set port speed 3/4,3/9-11,3/13-14,3/21,3/23-24 10

set port speed 3/2-3,3/5-8,3/12,3/15-20,3/22 100

set port duplex 3/8,3/12,3/15-16,3/18-19,3/22 full

set port duplex 3/2-7,3/9-11,3/13-14,3/17,3/20-21,3/23-24 half

set port trap 3/1-24 disable

set port name 3/2 PC Hubert

set port name 3/3 Result server D

set port name 3/5 Result server B

set port name 3/6 Result server A

set port name 3/7 Result server C

set port name 3/9 Router St.Jan2

set port name 3/15 Notes1

set port name 3/17 GinfoC08

set port name 3/18 Test Lode

set port name 3/19 SMS poort 1

set port name 3/20 GinfoC15

set port name 3/21 AS400 OCMW

set port name 3/22 Cluster1-prt6

set port name 3/24 CD-server

set port name 3/1,3/4,3/8,3/10-14,3/16,3/23

set port security 3/1-24 disable

set port security 3/1-24 maximum 1

set port security 3/1-24 violation shutdown

set port security 3/1-24 age 0

set port security 3/1-24 shutdown 0

set port broadcast 3/1-24 100%

set port membership 3/1-24 static

set port protocol 3/1-24 ip on

set port protocol 3/1-24 ipx auto

set port protocol 3/1-24 group auto

set port flowcontrol 3/1-24 send off

set port flowcontrol 3/1-24 receive on

set cdp enable 3/1-24

set udld disable 3/1-24

set trunk 3/1 auto negotiate 1-1005

set trunk 3/2 auto negotiate 1-1005

set trunk 3/3 auto negotiate 1-1005

set trunk 3/4 auto negotiate 1-1005

set trunk 3/5 auto negotiate 1-1005

set trunk 3/6 auto negotiate 1-1005

set trunk 3/7 auto negotiate 1-1005

set trunk 3/8 off dot1q 1-1005

set trunk 3/9 auto negotiate 1-1005

set trunk 3/10 auto negotiate 1-1005

set trunk 3/11 auto negotiate 1-1005

set trunk 3/12 auto negotiate 1-1005

set trunk 3/13 auto negotiate 1-1005

set trunk 3/14 auto negotiate 1-1005

set trunk 3/15 auto negotiate 1-1005

set trunk 3/16 auto negotiate 1-1005

set trunk 3/17 auto negotiate 1-1005

set trunk 3/18 auto negotiate 1-1005

set trunk 3/19 auto negotiate 1-1005

set trunk 3/20 auto negotiate 1-1005

set trunk 3/21 auto negotiate 1-1005

set trunk 3/22 auto negotiate 1-1005

set trunk 3/23 auto negotiate 1-1005

set trunk 3/24 auto negotiate 1-1005

set spantree portfast 3/1-24 enable

set spantree portcost 3/1-3,3/5-8,3/12,3/15-20,3/22 19

set spantree portcost 3/4,3/9-11,3/13-14,3/21,3/23-24 100

set spantree portpri 3/1-24 32

set spantree portvlanpri 3/1 0

set spantree portvlanpri 3/2 0

set spantree portvlanpri 3/3 0

set spantree portvlanpri 3/4 0

set spantree portvlanpri 3/5 0

set spantree portvlanpri 3/6 0

set spantree portvlanpri 3/7 0

set spantree portvlanpri 3/8 0

set spantree portvlanpri 3/9 0

set spantree portvlanpri 3/10 0

set spantree portvlanpri 3/11 0

set spantree portvlanpri 3/12 0

set spantree portvlanpri 3/13 0

set spantree portvlanpri 3/14 0

set spantree portvlanpri 3/15 0

set spantree portvlanpri 3/16 0

set spantree portvlanpri 3/17 0

set spantree portvlanpri 3/18 0

set spantree portvlanpri 3/19 0

set spantree portvlanpri 3/20 0

set spantree portvlanpri 3/21 0

set spantree portvlanpri 3/22 0

set spantree portvlanpri 3/23 0

set spantree portvlanpri 3/24 0

set spantree portvlancost 3/1 cost 18

set spantree portvlancost 3/2 cost 18

set spantree portvlancost 3/3 cost 18

set spantree portvlancost 3/4 cost 99

set spantree portvlancost 3/5 cost 18

set spantree portvlancost 3/6 cost 18

set spantree portvlancost 3/7 cost 18

set spantree portvlancost 3/8 cost 18

set spantree portvlancost 3/9 cost 99

set spantree portvlancost 3/10 cost 99

set spantree portvlancost 3/11 cost 99

set spantree portvlancost 3/12 cost 18

set spantree portvlancost 3/13 cost 99

set spantree portvlancost 3/14 cost 99

set spantree portvlancost 3/15 cost 18

set spantree portvlancost 3/16 cost 18

set spantree portvlancost 3/17 cost 18

set spantree portvlancost 3/18 cost 18

set spantree portvlancost 3/19 cost 18

set spantree portvlancost 3/20 cost 18

set spantree portvlancost 3/21 cost 99

set spantree portvlancost 3/22 cost 18

set spantree portvlancost 3/23 cost 99

set spantree portvlancost 3/24 cost 99

set port gvrp 3/1-24 disable

set gvrp registration normal 3/1-24

set gvrp applicant normal 3/1-24

set port gmrp 3/1-24 enable

set gmrp registration normal 3/1-24

set gmrp fwdall disable 3/1-24

set port channel 3/1-8 mode off

set port channel 3/9-24 mode auto silent

!

#module 4 : 24-port 10/100BaseTX Ethernet

set module name 4

set module enable 4

set vlan 2 4/1-12,4/14-24

set vlan 5 4/13

set port enable 4/1-24

set port level 4/1-24 normal

set port speed 4/5-6,4/11 auto

set port speed 4/10,4/13,4/20 10

set port speed 4/1-4,4/7-9,4/12,4/14-19,4/21-24 100

set port duplex 4/1-2,4/4,4/7-9,4/12,4/14-19,4/21-24 full

set port duplex 4/3,4/10,4/13,4/20 half

set port trap 4/1-24 disable

set port name 4/1 TD kaart 1

set port name 4/2 TD kaart 2

set port name 4/3 AS400C nw E45

set port name 4/13 Hub Jules

set port name 4/18 PC Olivier

set port name 4/19 cluster2-prt6

set port name 4/21 BDC

set port name 4/22 cluster1-prt5

set port name 4/23 GMKVGA09

set port name 4/24 SMS poort 2

set port name 4/4-12,4/14-17,4/20

set port security 4/1-24 disable

set port security 4/1-24 maximum 1

set port security 4/1-24 violation shutdown

set port security 4/1-24 age 0

set port security 4/1-24 shutdown 0

set port broadcast 4/1-24 100%

set port membership 4/1-24 static

set port protocol 4/1-24 ip on

set port protocol 4/1-24 ipx auto

set port protocol 4/1-24 group auto

set port flowcontrol 4/1-24 send off

set port flowcontrol 4/1-24 receive on

set cdp enable 4/1-24

set udld disable 4/1-24

set trunk 4/1 auto negotiate 1-1005

set trunk 4/2 auto negotiate 1-1005

set trunk 4/3 auto negotiate 1-1005

set trunk 4/4 auto negotiate 1-1005

set trunk 4/5 auto negotiate 1-1005

set trunk 4/6 auto negotiate 1-1005

set trunk 4/7 auto negotiate 1-1005

set trunk 4/8 auto negotiate 1-1005

set trunk 4/9 auto negotiate 1-1005

set trunk 4/10 auto negotiate 1-1005

set trunk 4/11 auto negotiate 1-1005

set trunk 4/12 auto negotiate 1-1005

set trunk 4/13 auto negotiate 1-1005

set trunk 4/14 auto negotiate 1-1005

set trunk 4/15 auto negotiate 1-1005

set trunk 4/16 auto negotiate 1-1005

set trunk 4/17 auto negotiate 1-1005

set trunk 4/18 auto negotiate 1-1005

set trunk 4/19 auto negotiate 1-1005

set trunk 4/20 auto negotiate 1-1005

set trunk 4/21 auto negotiate 1-1005

set trunk 4/22 auto negotiate 1-1005

set trunk 4/23 off negotiate 1-1005

set trunk 4/24 auto negotiate 1-1005

set spantree portfast 4/1-17,4/19-24 enable

set spantree portfast 4/18 disable

set spantree portcost 4/1-9,4/12,4/14-19,4/21-24 19

set spantree portcost 4/10-11,4/13,4/20 100

set spantree portpri 4/1-24 32

set spantree portvlanpri 4/1 0

set spantree portvlanpri 4/2 0

set spantree portvlanpri 4/3 0

set spantree portvlanpri 4/4 0

set spantree portvlanpri 4/5 0

set spantree portvlanpri 4/6 0

set spantree portvlanpri 4/7 0

set spantree portvlanpri 4/8 0

set spantree portvlanpri 4/9 0

set spantree portvlanpri 4/10 0

set spantree portvlanpri 4/11 0

set spantree portvlanpri 4/12 0

set spantree portvlanpri 4/13 0

set spantree portvlanpri 4/14 0

set spantree portvlanpri 4/15 0

set spantree portvlanpri 4/16 0

set spantree portvlanpri 4/17 0

set spantree portvlanpri 4/18 0

set spantree portvlanpri 4/19 0

set spantree portvlanpri 4/20 0

set spantree portvlanpri 4/21 0

set spantree portvlanpri 4/22 0

set spantree portvlanpri 4/23 0

set spantree portvlanpri 4/24 0

set spantree portvlancost 4/1 cost 18

set spantree portvlancost 4/2 cost 18

set spantree portvlancost 4/3 cost 18

set spantree portvlancost 4/4 cost 18

set spantree portvlancost 4/5 cost 18

set spantree portvlancost 4/6 cost 18

set spantree portvlancost 4/7 cost 18

set spantree portvlancost 4/8 cost 18

set spantree portvlancost 4/9 cost 18

set spantree portvlancost 4/10 cost 99

set spantree portvlancost 4/11 cost 99

set spantree portvlancost 4/12 cost 18

set spantree portvlancost 4/13 cost 99

set spantree portvlancost 4/14 cost 18

set spantree portvlancost 4/15 cost 18

set spantree portvlancost 4/16 cost 18

set spantree portvlancost 4/17 cost 18

set spantree portvlancost 4/18 cost 18

set spantree portvlancost 4/19 cost 18

set spantree portvlancost 4/20 cost 99

set spantree portvlancost 4/21 cost 18

set spantree portvlancost 4/22 cost 18

set spantree portvlancost 4/23 cost 18

set spantree portvlancost 4/24 cost 18

set port gvrp 4/1-24 disable

set gvrp registration normal 4/1-24

set gvrp applicant normal 4/1-24

set port gmrp 4/1-24 enable

set gmrp registration normal 4/1-24

set gmrp fwdall disable 4/1-24

set port channel 4/1-2 mode on

set port channel 4/3-24 mode auto silent

!

#module 5 : 24-port 10/100BaseTX Ethernet

set module name 5

set module enable 5

set vlan 1 5/24

set vlan 2 5/1-23

set port enable 5/1-24

set port level 5/1-24 normal

set port speed 5/4,5/6-8,5/10,5/14,5/18,5/22,5/24 auto

set port speed 5/1-3,5/5,5/9,5/11-13,5/15-17,5/19-21,5/23 100

set port duplex 5/1-3,5/5,5/9,5/11-13,5/15-17,5/19,5/21,5/23 full

set port duplex 5/20 half

set port trap 5/1-24 disable

set port name 5/1 GZOLSA01-2

set port name 5/2 GZOLSA01-1

set port name 5/3 GZOLSA03

set port name 5/5 Server P&C

set port name 5/9 Notes2

set port name 5/11 AS400C port 1

set port name 5/12 AS400C port 2

set port name 5/15 voorlopige datagate1

set port name 5/16 voorlopige datagate2

set port name 5/17 server MKA

set port name 5/19 cluster2-prt5

set port name 5/20 AS400C nw E44

set port name 5/23 PC Olivier

set port name 5/24 Upl to C2924M-XL_SAN

set port name 5/4,5/6-8,5/10,5/13-14,5/18,5/21-22

set port security 5/1-24 disable

set port security 5/1-24 maximum 1

set port security 5/1-24 violation shutdown

set port security 5/1-24 age 0

set port security 5/1-24 shutdown 0

set port broadcast 5/1-24 100%

set port membership 5/1-24 static

set port protocol 5/1-24 ip on

set port protocol 5/1-24 ipx auto

set port protocol 5/1-24 group auto

set port flowcontrol 5/1-24 send off

set port flowcontrol 5/1-24 receive on

set cdp enable 5/1-24

set udld disable 5/1-24

set trunk 5/1 auto negotiate 1-1005

set trunk 5/2 auto negotiate 1-1005

set trunk 5/3 auto negotiate 1-1005

set trunk 5/4 auto negotiate 1-1005

set trunk 5/5 on isl 1-1005

set trunk 5/6 auto negotiate 1-1005

set trunk 5/7 auto negotiate 1-1005

set trunk 5/8 auto negotiate 1-1005

set trunk 5/9 auto negotiate 1-1005

set trunk 5/10 auto negotiate 1-1005

set trunk 5/11 auto negotiate 1-1005

set trunk 5/12 auto negotiate 1-1005

set trunk 5/13 auto negotiate 1-1005

set trunk 5/14 auto negotiate 1-1005

set trunk 5/15 auto negotiate 1-1005

set trunk 5/16 auto negotiate 1-1005

set trunk 5/17 auto negotiate 1-1005

set trunk 5/18 auto negotiate 1-1005

set trunk 5/19 auto negotiate 1-1005

set trunk 5/20 auto negotiate 1-1005

set trunk 5/21 off dot1q 1-1005

set trunk 5/22 auto negotiate 1-1005

set trunk 5/23 auto negotiate 1-1005

set trunk 5/24 on dot1q 1-1005

set spantree portfast 5/1-5,5/7-23 enable

set spantree portfast 5/6,5/24 disable

set spantree portcost 5/1-24 19

set spantree portpri 5/1-24 32

set spantree portvlanpri 5/1 0

set spantree portvlanpri 5/2 0

set spantree portvlanpri 5/3 0

set spantree portvlanpri 5/4 0

set spantree portvlanpri 5/5 32 1-1005

set spantree portvlanpri 5/6 0

set spantree portvlanpri 5/7 0

set spantree portvlanpri 5/8 0

set spantree portvlanpri 5/9 0

set spantree portvlanpri 5/10 0

set spantree portvlanpri 5/11 0

set spantree portvlanpri 5/12 0

set spantree portvlanpri 5/13 0

set spantree portvlanpri 5/14 0

set spantree portvlanpri 5/15 0

set spantree portvlanpri 5/16 0

set spantree portvlanpri 5/17 0

set spantree portvlanpri 5/18 0

set spantree portvlanpri 5/19 0

set spantree portvlanpri 5/20 0

set spantree portvlanpri 5/21 0

set spantree portvlanpri 5/22 0

set spantree portvlanpri 5/23 0

set spantree portvlanpri 5/24 0

set spantree portvlancost 5/1 cost 18

set spantree portvlancost 5/2 cost 18

set spantree portvlancost 5/3 cost 18

set spantree portvlancost 5/4 cost 18

set spantree portvlancost 5/5 cost 18

set spantree portvlancost 5/6 cost 18

set spantree portvlancost 5/7 cost 18

set spantree portvlancost 5/8 cost 18

set spantree portvlancost 5/9 cost 18

set spantree portvlancost 5/10 cost 18

set spantree portvlancost 5/11 cost 18

set spantree portvlancost 5/12 cost 18

set spantree portvlancost 5/13 cost 18

set spantree portvlancost 5/14 cost 18

set spantree portvlancost 5/15 cost 18

set spantree portvlancost 5/16 cost 18

set spantree portvlancost 5/17 cost 18

set spantree portvlancost 5/18 cost 18

set spantree portvlancost 5/19 cost 18

set spantree portvlancost 5/20 cost 18

set spantree portvlancost 5/21 cost 18

set spantree portvlancost 5/22 cost 18

set spantree portvlancost 5/23 cost 18

set spantree portvlancost 5/24 cost 18

set port gvrp 5/1-24 disable

set gvrp registration normal 5/1-24

set gvrp applicant normal 5/1-24

set port gmrp 5/1-24 enable

set gmrp registration normal 5/1-24

set gmrp fwdall disable 5/1-24

set port channel 5/1-24 mode auto silent

!

#module 6 : 3-port 1000BaseX Ethernet

set module name 6

set module enable 6

set vlan 1 6/1-3

set port enable 6/1-3

set port level 6/1-3 normal

set port trap 6/1-3 disable

set port name 6/2 to_C2924M-XL_B10

set port name 6/1,6/3

set port broadcast 6/1-3 100%

set port protocol 6/1-3 ip on

set port protocol 6/1-3 ipx auto

set port protocol 6/1-3 group auto

set port flowcontrol 6/1-3 send desired

set port flowcontrol 6/1-3 receive off

set cdp enable 6/1-3

set udld enable 6/1-3

set trunk 6/1 on dot1q 1-1005

set trunk 6/2 on dot1q 1-1005

set trunk 6/3 on dot1q 1-1005

set spantree portfast 6/1-3 disable

set spantree portcost 6/1-3 4

set spantree portpri 6/1-3 32

set spantree portvlanpri 6/1 0

set spantree portvlanpri 6/2 0

set spantree portvlanpri 6/3 0

set spantree portvlancost 6/1 cost 3

set spantree portvlancost 6/2 cost 3

set spantree portvlancost 6/3 cost 3

set port gvrp 6/1-3 disable

set gvrp registration normal 6/1-3

set gvrp applicant normal 6/1-3

set port gmrp 6/1-3 enable

set gmrp registration normal 6/1-3

set gmrp fwdall disable 6/1-3

!

#module 7 empty

!

#module 8 : 9-port Gigabit Ethernet

set module name 8

set module enable 8

set vlan 1 8/1-9

set port enable 8/1-9

set port level 8/1-9 normal

set port trap 8/1-9 disable

set port name 8/5 upl C3548A10A prt1/0

set port name 8/1-4,8/6-9

set port security 8/1-9 disable

set port security 8/1-9 maximum 1

set port security 8/1-9 violation shutdown

set port security 8/1-9 age 0

set port security 8/1-9 shutdown 0

set port broadcast 8/1-9 0

set port membership 8/1-9 static

set port protocol 8/1-9 ip on

set port protocol 8/1-9 ipx auto

set port protocol 8/1-9 group auto

set port flowcontrol 8/1-9 send desired

set port flowcontrol 8/1-9 receive off

set cdp enable 8/1-9

set udld enable 8/1-9

set trunk 8/1 on dot1q 1-1005

set trunk 8/2 on dot1q 1-1005

set trunk 8/3 on dot1q 1-1005

set trunk 8/4 on dot1q 1-1005

set trunk 8/5 on dot1q 1-1005

set trunk 8/6 on dot1q 1-1005

set trunk 8/7 on dot1q 1-1005

set trunk 8/8 on dot1q 1-1005

set trunk 8/9 on dot1q 1-1005

set spantree portfast 8/1-9 disable

set spantree portcost 8/1-9 4

set spantree portpri 8/1-9 32

set spantree portvlanpri 8/1 0

set spantree portvlanpri 8/2 0

set spantree portvlanpri 8/3 0

set spantree portvlanpri 8/4 0

set spantree portvlanpri 8/5 0

set spantree portvlanpri 8/6 0

set spantree portvlanpri 8/7 0

set spantree portvlanpri 8/8 0

set spantree portvlanpri 8/9 0

set spantree portvlancost 8/1 cost 3

set spantree portvlancost 8/2 cost 3

set spantree portvlancost 8/3 cost 3

set spantree portvlancost 8/4 cost 3

set spantree portvlancost 8/5 cost 3

set spantree portvlancost 8/6 cost 3

set spantree portvlancost 8/7 cost 3

set spantree portvlancost 8/8 cost 3

set spantree portvlancost 8/9 cost 3

set port gvrp 8/1-9 disable

set gvrp registration normal 8/1-9

set gvrp applicant normal 8/1-9

set port gmrp 8/1-9 enable

set gmrp registration normal 8/1-9

set gmrp fwdall disable 8/1-9

set port channel 8/1-9 mode auto non-silent

!

#module 9 empty

!

#module 15 empty

!

#module 16 empty

!

#switch port analyzer

!

#cam

set cam agingtime 1-5,1003,1005 300

!

#qos mac-cos

!

#gvrp

set gvrp dynamic-vlan-creation disable

set gvrp disable

end

1 ACCEPTED SOLUTION

Accepted Solutions
Blue

Re: LMS Real time monitor and Catalyst 5509

What is the version of RTM that you're using?. In order to use RTM on switches running CatOS (5K/6K etc), you must first enable mini-rmon on the switch. Without it you cannot monitor the mini-rmon stats using RTM at all NOR will RTM enable it for you automatically if it's disabled (which is the case here). Secondly, with only mini-rmon enabled on the switch, you can only see upto the Data Link Layer stats in Traffic Monitor. To see Network/Application Layer data, you must ahve a switch probe/NAM physically connected to the probe and spanned as well. So, you need to do the following:

-Delete the switch from RTM server

- Enable mini-rmon on the switch using the CLI command 'set snmp rmon enable'. I do believe that enabling mini-rmon on the switch requires a license first: http://www.cisco.com/warp/public/cc/pd/si/casi/ca4000/prodlit/909_pb.htm

- Do a 'sh snmp' on the switch to make sure that RMON shows as enabled in the output.

- Add the switch back again in RTM Server using it's ip, SNMP strings etc. Do not use Automatic option in the Switch Type pull-down menu. Select the actual switch model from the list. Once the switch gets added, go back to Traffic Monitor to see the stats.

1 REPLY
Blue

Re: LMS Real time monitor and Catalyst 5509

What is the version of RTM that you're using?. In order to use RTM on switches running CatOS (5K/6K etc), you must first enable mini-rmon on the switch. Without it you cannot monitor the mini-rmon stats using RTM at all NOR will RTM enable it for you automatically if it's disabled (which is the case here). Secondly, with only mini-rmon enabled on the switch, you can only see upto the Data Link Layer stats in Traffic Monitor. To see Network/Application Layer data, you must ahve a switch probe/NAM physically connected to the probe and spanned as well. So, you need to do the following:

-Delete the switch from RTM server

- Enable mini-rmon on the switch using the CLI command 'set snmp rmon enable'. I do believe that enabling mini-rmon on the switch requires a license first: http://www.cisco.com/warp/public/cc/pd/si/casi/ca4000/prodlit/909_pb.htm

- Do a 'sh snmp' on the switch to make sure that RMON shows as enabled in the output.

- Add the switch back again in RTM Server using it's ip, SNMP strings etc. Do not use Automatic option in the Switch Type pull-down menu. Select the actual switch model from the list. Once the switch gets added, go back to Traffic Monitor to see the stats.

106
Views
0
Helpful
1
Replies
CreatePlease to create content