Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

NAM-2 and WS-F6K-MSFC Compatibility

Can anyone please tell me if I'm able to get the full functionality when I "only" have a WS-F6K-MSFC installed in my 6509 or should it be a MSFC2 ?.

I'm a little bit confused because somewhere on CCO I have find that the requirement is MSFC2 and in some examples I have seen the configuraton listed with just a MSFC so whats correct ?.

Thanks

Senior Network Enginer

Flemming Iversen

CSC Scandinavia

4 REPLIES
Blue

Re: NAM-2 and WS-F6K-MSFC Compatibility

For NAM-2, you need to have a MSFC2. See the section "Table 3 and Table4" at: http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_14487.htm#xtocid12 for details.

New Member

Re: NAM-2 and WS-F6K-MSFC Compatibility

Hi

Thanks for your quick response.

What about if I'm buying a MSFC1 because if you look in the "show module" example below Table 5 on the same page there is shown a MSFC.

Console> (enable) show module

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC no ok

3 3 2 Network Analysis Module WS-SVC-NAM-1 no ok

5 5 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

.

Can you tell me whats happen if I install a MSFC2 in my 6509. I'll think

it would be wery nice to have support for dual SPAN sessions but I dont want to by new Supervisor engines.

My setup:

CSC-RSW1-MS3> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC no ok

2 2 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes standby

16 2 1 Multilayer Switch Feature WS-F6K-MSFC no ok

3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok

4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok

7 7 16 1000BaseSX Ethernet WS-X6416-GE-MT no ok

8 8 16 1000BaseSX Ethernet WS-X6416-GE-MT no ok

9 9 2 MM OC-12 ATM WS-X6101-OC12-MMF no ok

Kind regards

Flemming Iversen

Blue

Re: NAM-2 and WS-F6K-MSFC Compatibility

I haven't tested NAM-2 with MSFC1, therefore I don't know whether it will work or not. But I'd prefer going by the NAM docs to be on the safe side.

New Member

Re: NAM-2 and WS-F6K-MSFC Compatibility

Sorry Rizwan

I ment buying a NAM-1 not a MSFC-1. ;-)

137
Views
0
Helpful
4
Replies