Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Network card MN-2CE1B

Hello!

Could anyone explain me why does a MN-2CE1B show up as "unbalanced"? (see the output of commands sh contr e1 and sh diag below). Acording to the specs this is balanced card.

Router#sh controllers E1

E1 1/0 is down.

Applique type is Channelized E1 - unbalanced

Transmitter is sending remote alarm.

Receiver has loss of signal.

Framing is CRC4, Line Code is HDB3, Clock Source is Line.

Data in current interval (430 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 430 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 430 Unavail Secs

Total Data (last 1 15 minute intervals):

0 Line Code Violations, 0 Path Code Violations,

1 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs

E1 1/1 is down.

Applique type is Channelized E1 - unbalanced

Transmitter is sending remote alarm.

Receiver has loss of signal.

Framing is CRC4, Line Code is HDB3, Clock Source is Line.

Data in current interval (440 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 440 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 440 Unavail Secs

Total Data (last 1 15 minute intervals):

0 Line Code Violations, 0 Path Code Violations,

1 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs

Router#sh diag

Slot 0:

C2612 1E1R Mainboard port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision A0

Serial number 692912706 Part number 73-2841-06

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 93 01 01 29 4D 02 42 49 0B 19 06 00 00 00 00

0x30: 50 00 00 06 00 00 00 00 00 00 00 00 00 00 00 00

Slot 1:

CE1 (Unbalanced) port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision C0

Serial number 28612578 Part number 800-02117-04

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 3B 01 01 01 B4 97 E2 50 08 45 04 00 00 00 00

0x30: 60 00 00 00 01 09 10 00 FF FF FF FF FF FF FF FF

Thank you in advance.

Viktor.

6 REPLIES
Silver

Re: Network card MN-2CE1B

Check for the labelling and whether you have bought the correct card type or there is any mismatch in the labeling of the card.

New Member

Re: Network card MN-2CE1B

Balanced type has a 120 ohm RJ-45 type connector whereas unbalanced has BNC 75 ohm type connector.

Bronze

Re: Network card MN-2CE1B

I think you're confused with E3 or other cards.

NM-xCE1x cards all have a DB15 connector.

http://www.cisco.com/en/US/customer/products/hw/modules/ps2797/products_tech_note09186a00800b1150.shtml

Silver

Re: Network card MN-2CE1B

New Member

Re: Network card MN-2CE1B

Thank You guys for your answers. I contacted Cisco TAC and its 99% mistake at Cisco plant. Modules, bags and boxes marked as MN-2CE1B, but modules are MN-2CE1U indeed.

New Member

Re: Network card MN-2CE1B

Hi,

On NM-2CE1B there is a jumper to switch from balanced to unbalanced. Position 1-2 for unbalanced and 2-3 for balanced.

Regards

Jawwad

jawwadh19@yahoo.com

158
Views
0
Helpful
6
Replies