Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

NME1 (E1 modules)DOESNT SHOW in INterfaces.

Hi ,

I have some 6 e1 modules which i have tested with my 3 cisco 2621 routers all of them give the same result,the bootstrap recognizes it but after that the modules wont load and doesnt show in the running config.is there a compatibility issue ? im attaching the log.

------------------------------------------------------------

System Bootstrap, Version 12.2(6r), RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 2001 by cisco Systems, Inc.

C2600 platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x5014f0

Self decompressing the image :

[OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0000A2 0X0010A400 C2600 Dual Fast Ethernet

00002A 0X0019CB00 Single port Channelized E1 (120 Ohm - TP)

0X000F3BB0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X005ABAB0

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 6Mb.

Using 18 percent iomem. [6Mb/32Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-I-M), Version 12.2(5d), RELEASE SOFTWARE

(fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Sat 02-Feb-02 03:36 by kellythw

Image text-base: 0x80008088, data-base: 0x80989870

cisco 2621 (MPC860) processor (revision 0x00) with 26624K/6144K bytes

of memory.

Processor board ID JAD06300HM3 (2337219636)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: N

Press RETURN to get started!

00:00:05: %PA-2-UNDEFPA: Undefined Port Adaptor type 65535 in bay 1

00:00:06: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to

up

00:00:06: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to

up

00:00:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface

FastEthernet0/0, changed state to down

00:00:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface

FastEthernet0/1, changed state to down

00:00:26: %IP-5-WEBINST_KILL: Terminating DNS process

00:00:27: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to

administratively down

00:00:27: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to

administratively down

00:00:28: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-I-M), Version 12.2(5d), RELEASE SOFTWARE

(fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Sat 02-Feb-02 03:36 by kellythw

00:00:28: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a

cold start

Router>

Router>(in runing config modules doesnt show)

I have also tried changing IOS.

1 ACCEPTED SOLUTION

Accepted Solutions
New Member

Re: NME1 (E1 modules)DOESNT SHOW in INterfaces.

Hi,

00:00:05: %PA-2-UNDEFPA: Undefined Port Adaptor type 65535 in bay 1 - this tells You that Your IOS has no support for this type of NM. I thhink, this module is not supported on 2621 router or You might require T version of IOS, like 12.2.8.T5 or similar. Check CCO for compatibility matrix

Hope that helps

Giedrius

4 REPLIES
New Member

Re: NME1 (E1 modules)DOESNT SHOW in INterfaces.

Are you using this NM-1CE1B or NM-1CE1U module? Or do you really mean 6 port Channelized E1 NM?

The 2600 supports 1/2 port NMs

http://www.cisco.com/warp/public/cc/pd/rt/3600/prodlit/vwic2_ds.htm

Is this what you have?

New Member

Re: NME1 (E1 modules)DOESNT SHOW in INterfaces.

Hi,

00:00:05: %PA-2-UNDEFPA: Undefined Port Adaptor type 65535 in bay 1 - this tells You that Your IOS has no support for this type of NM. I thhink, this module is not supported on 2621 router or You might require T version of IOS, like 12.2.8.T5 or similar. Check CCO for compatibility matrix

Hope that helps

Giedrius

New Member

Re: NME1 (E1 modules)DOESNT SHOW in INterfaces.

hi,

The module is NM1CE1B ,i will try dowloading the T series IOS.how do i check compatibilty matrix.

Regards

New Member

Re: NME1 (E1 modules)DOESNT SHOW in INterfaces.

252
Views
0
Helpful
4
Replies