Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

No bootflash after format.

Have Sup2 cards with MSFC2 cards running active and Hot on a 6509 switch. Went to copy my boot code onto my slavebootflash, but after I formated the slavebootflash, it was no longer there. I get an error; "%Error opening slavebootflash:/ (Bad device info block)" If I do a "dir all", the slavebootflash does not even show up. How do I get it back? I have read a couple of entries where reseting the standby sup card may bring it back but it was not definitive. Any ideas before I open a TAC? I am running 12.1 (18 SXD4)

2 REPLIES
Cisco Employee

Re: No bootflash after format.

What is the status of your standby Sup? Can you paste output of sh mod?

New Member

Re: No bootflash after format.

Standby is Hot. See below

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE SAL09253XH6

2 2 Catalyst 6000 supervisor 2 (Hot) WS-X6K-SUP2-2GE SAL09253W0R

3 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL09253QMH

4 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL09253QPM

5 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL09253QMD

6 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL09253QP5

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0005.7440.5a0c to 0005.7440.5a0d 5.3 7.1(1) 12.2(18)SXD4 Ok

2 0005.7440.5900 to 0005.7440.5901 5.3 7.1(1) 12.2(18)SXD4 Ok

3 0014.6ae9.4898 to 0014.6ae9.48c7 10.0 8.3(1) 8.3(0.156)RO Ok

4 0014.6ae9.2cd8 to 0014.6ae9.2d07 10.0 8.3(1) 8.3(0.156)RO Ok

5 0014.a849.d4a8 to 0014.a849.d4d7 10.0 8.3(1) 8.3(0.156)RO Ok

6 0009.125d.0fb8 to 0009.125d.0fe7 10.0 8.3(1) 8.3(0.156)RO Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- ------------------ ------------ ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 SAL09253S6U 3.5 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL09018BXK 2.8 Ok

2 Policy Feature Card 2 WS-F6K-PFC2 SAL09253S2Q 3.5 Ok

2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL085284U0 2.8 Ok

Mod Online Diag Status

--- -------------------

1 Pass

2 Pass

3 Pass

4 Pass

5 Pass

6 Pass

154
Views
0
Helpful
2
Replies
CreatePlease to create content