Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Not able to enable web access (http server) on 5500

Hi

i have 5500 Swtich iam not able to enable http server in it

the message show below

Core-Switch> (enable) show ip http

HTTP Information

----------------------

HTTP server: disabled

HTTP port: 800

Web Interface: Not supported

HTTP active sessions: 0

Core-Switch> (enable) show ver

WS-C5500 Software, Version McpSW: 5.5(18) NmpSW: 5.5(18)

Copyright (c) 1995-2002 by Cisco Systems

NMP S/W compiled on Dec 16 2002, 15:34:48

MCP S/W compiled on Dec 16 2002, 15:30:03

System Bootstrap Version: 3.1.2

Hardware Version: 1.4 Model: WS-C5500 Serial #: 069062010

Mod Port Model Serial # Versions

--- ---- ---------- --------- ----------------------------------------

1 2 WS-X5530 008731527 Hw : 1.8

Fw : 3.1.2

Fw1: 4.1(1)

Sw : 5.5(18)

WS-F5520 008715296 Hw : 1.1

WS-U5533 009612560 Hw : 1.0

2 2 WS-X5530 008146970 Hw : 1.5

Fw : 3.1.2

Fw1: 3.1(2)

Sw : 5.5(18)

WS-F5520 007590229 Hw : 1.0

WS-U5533 009613415 Hw : 1.0

3 24 WS-X5234 022374107 Hw : 1.0

Fw : 4.5(2)

Sw : 5.5(18)

4 24 WS-X5234 018022744 Hw : 1.0

Fw : 4.5(2)

Sw : 5.5(18)

5 24 WS-X5234 018025296 Hw : 1.0

Fw : 4.5(2)

Sw : 5.5(18)

6 24 WS-X5234 017582607 Hw : 1.0

Fw : 4.5(2)

Sw : 5.5(18)

7 24 WS-X5234 017919621 Hw : 1.0

Fw : 4.5(2)

Sw : 5.5(18)

10 1 WS-X5304 024975347 Hw : 7.7

Fw : 20.22

Fw1: 3.1(1)

Sw : 12.1(20)

4 REPLIES
Blue

Re: Not able to enable web access (http server) on 5500

have you run the 'set ip http server enable' command at the CatOS CLI of the 5500?

as you've shown above, it is currently disabled

does the switch have an ip address assigned to interface SC0? does SC0 belong to an inactive VLAN?

if the switch OS does not support it, it should display an error as follows when you type in the command: (as shown below)

console> set ip http server enable

Feature not supported on the system.

Purple

Re: Not able to enable web access (http server) on 5500

This will not work unless you have the ciscoview adp flash code on your switch. Do a "dir bootflash: or dir slot0: depending on where your image is . It should look like the follwing with the "cv" in the name if not you can't run http server.

cat5000-sup3cv.6-4-16.bin

Community Member

Re: Not able to enable web access (http server) on 5500

Hi

when i try enable

its says the below command

Core-Switch> (enable) set ip http server enable

Feature not supported.

1 4976713 Jun 08 2004 16:21:39 cat5000-sup3.5-5-18.bin

Purple

Re: Not able to enable web access (http server) on 5500

As it indicates it's not supported you do not have the right catos code installed. It's easier to manage via the command line anyway...

263
Views
0
Helpful
4
Replies
CreatePlease to create content