08-20-2003 05:14 PM - edited 03-02-2019 09:46 AM
Hi,
The two router (routerA and routerB) are connected via frame-relay point-to-point nonbroadcast network using OSPF as routing protocol.
router A
int s0/0.1 is on 1.1.1.0 network
int s0/1.1 is on 2.2.2.0 network
int f0/0 is on 3.3.3.0 network
router B
int s0/0.1 is on 1.1.1.0 network
int s01.1 is on 20.20.20.0 network
int f0/0 is on 30.30.30.0 network
since 1.1.1.0 network is a nonbroadcast network so it will not exchange the OSPF routes if I am right.
If I want to tell RouterA about 20.20.20.0 and 30.30.30.0 (same for RouterB about 2.2.2.0 and 1.1.1.0) do I have to use ospf neighbor command (if yes how should I use it) and is there anything else I can do, I dont want to use static routes.
Thanks
Solved! Go to Solution.
08-20-2003 06:00 PM
Are the subinterfaces defined as point-to-point? If so, just put in ospf network statements on both routers, and it should just work. If they are defined as multipoint subs--I would first reconsider, and make them point-to-point subinterfaces, unless you are really going to have more than one remote attached to the same subinterface. If you must leave them configured as point-to-multipoints, then you have a couple of options:
-- Configure the subinterface as nonbroadcast, and manually define the ospf neighbor on the other end. Configure ospf with the right network statements, and this should work.
-- Configure the subinterface as a point-to-multipoint.
-- Configure the subinterfaces as broadcast networks, and configure the ospf priority on the "hub" router so it's always the DR.
http://www.cisco.com/en/US/tech/tk365/tk480/technologies_tech_note09186a008009470d.shtml
http://www.cisco.com/en/US/tech/tk365/tk480/technologies_configuration_example09186a0080094054.shtml
http://www.cisco.com/en/US/tech/tk365/tk480/technologies_tech_note09186a0080094051.shtml
One of these should help. The way I would do it would be to define those subinterfaces as point-to-point. That's the simplest/easiest way around it.
Russ.W
08-20-2003 06:00 PM
Are the subinterfaces defined as point-to-point? If so, just put in ospf network statements on both routers, and it should just work. If they are defined as multipoint subs--I would first reconsider, and make them point-to-point subinterfaces, unless you are really going to have more than one remote attached to the same subinterface. If you must leave them configured as point-to-multipoints, then you have a couple of options:
-- Configure the subinterface as nonbroadcast, and manually define the ospf neighbor on the other end. Configure ospf with the right network statements, and this should work.
-- Configure the subinterface as a point-to-multipoint.
-- Configure the subinterfaces as broadcast networks, and configure the ospf priority on the "hub" router so it's always the DR.
http://www.cisco.com/en/US/tech/tk365/tk480/technologies_tech_note09186a008009470d.shtml
http://www.cisco.com/en/US/tech/tk365/tk480/technologies_configuration_example09186a0080094054.shtml
http://www.cisco.com/en/US/tech/tk365/tk480/technologies_tech_note09186a0080094051.shtml
One of these should help. The way I would do it would be to define those subinterfaces as point-to-point. That's the simplest/easiest way around it.
Russ.W
08-20-2003 06:22 PM
Hi Russ,
I have defined subinterfaces as point-to-point.
So should I use "ip ospf network broadcast"
and thanks for the doco links.
Nitin
08-21-2003 02:01 AM
I'd leave them as point-to-point, and just put in a network statement under router ospf to include them in the ospf process.
Russ.W
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: