Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

OSPF pb

Hi,

I have 2 routers 7513 connected via a satellite link (HSSI interface with QoS configure on it) and some times (it is appenning very ramdomly) the link is falling down during 2 mn.

Here are the conf and logs :

router #1

interface Hssi8/0/0

description *** Liaison Satellite ***

bandwidth 12000

ip address 192.168.201.2 255.255.255.248

max-reserved-bandwidth 80

service-policy output POL2

serial restart-delay 0

Nov 6 15:40:56.537: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.211.26 on Hssi8/0/0 from FULL to DOWN, Neighbor Down: Dead timer expired

Nov 6 15:41:28.180: %LINEPROTO-5-UPDOWN: Line protocol on Interface Hssi8/0/0, changed state to down

Nov 6 15:41:28.248: %STANDBY-6-STATECHANGE: FastEthernet4/0/0.1 Group 0 state Active -> Speak

Nov 6 15:42:28.026: %STANDBY-6-STATECHANGE: FastEthernet4/0/0.1 Group 0 state Standby -> Active

Nov 6 15:42:28.178: %LINEPROTO-5-UPDOWN: Line protocol on Interface Hssi8/0/0, changed state to up

Nov 6 15:42:38.086: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.211.26 on Hssi8/0/0 from LOADING to FULL, Loading Done

-------------------------------------

router #2

interface Hssi8/1/0

description *** Liaison satellite ***

bandwidth 12000

ip address 192.168.201.1 255.255.255.248

max-reserved-bandwidth 80

service-policy output POL2

serial restart-delay 0

Nov 6 15:42:07.178: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.211.25 on Hssi8/1/0 from INIT to DOWN, Neighbor Down: Dead timer expired

Nov 6 15:42:11.602: %LINEPROTO-5-UPDOWN: Line protocol on Interface Hssi8/1/0, changed state to down

Nov 6 15:42:13.606: %LINEPROTO-5-UPDOWN: Line protocol on Interface Hssi8/1/0, changed state to up

Nov 6 15:42:38.346: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.211.25 on Hssi8/1/0 from LOADING to FULL, Loading Done

-----------------------------------------------------

Thks for ur help

5 REPLIES
Cisco Employee

Re: OSPF pb

This is not an OSPF problem. The link is going down. OSPF is just reacting to it.

Harold Ritter
Sr. Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México 
Paseo de la Reforma 222 Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
New Member

Re: OSPF pb

My understanding is that satellite connections can experience delay.

Based upon your logging, suggest that the interval between ospf hello packets may be causing your outages. Suggest that adjusting the ospf dead interval from its default of four times the hello interval (default 10 seconds) may remedy your situation.

ip ospf dead-interval 50

Good luck!

Cisco Employee

Re: OSPF pb

Changing the OSPF dead timer won't change anything by itself since the adjacency will be reset as the link is declared down:

Nov 6 15:42:11.602: %LINEPROTO-5-UPDOWN: Line protocol on Interface Hssi8/1/0, changed state to down

HDLC will wait 40 seconds before it considers the interface down if it doesn't receive keepalives.

Tell me if I'm wrong but the normal delay for a satellite link is about ~250 ms.

Harold Ritter
Sr. Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México 
Paseo de la Reforma 222 Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
Cisco Employee

Re: OSPF pb

Correction. A satellite link propagation delay is ~250ms up and ~250ms down = ~500ms total. The point is the problem is unlikely related to the propagation delay.

Harold Ritter
Sr. Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México 
Paseo de la Reforma 222 Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
New Member

Re: OSPF pb

you're right. The propagation delay (ICMP request) is around 520 ms depending on the data rate and the satellite equipement.

I've found this bug (cscdv28293) about QoS and HSSI but my release (12.2 10.6)is not concerned :

"Add service-policy output to HSSI interface may cause the interface down.There is no workaround."

thks again for ur help

flavien

364
Views
0
Helpful
5
Replies
CreatePlease login to create content