Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

output error in int g49 cat 2948g-l3

INTER_VLAN#sh int g49

GigabitEthernet49 is up, line protocol is up

Hardware is xpif_port, address is 0007.50fe.2507 (bia 0007.50fe.2507)

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, rely 248/255, load 1/255

Encapsulation ARPA, loopback not set, keepalive set (10 sec)

Full-duplex, 1000Mb/s, 1000Base-SX, Force link-up

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 670000 bits/sec, 151 packets/sec

5 minute output rate 653000 bits/sec, 111 packets/sec

119959192 packets input, 3850534723 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 watchdog, 135346242 multicast

0 input packets with dribble condition detected

90488747 packets output, 1604713883 bytes, 0 underruns

0 1-collision pkt cntrs, 0 more-collision pkt cntrs,

0 excessive-collision pkt cntrs

79290942 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

INTER_VLAN#sh controllers gigabitEthernet 49

IF Name: GigabitEthernet49

Port Status UP

GBIC : Enabled

Internal Reset Trigger Count : 0

Slicer registers

SMDR 0xFF78 SSTR 0x1202 SSMR 0x4102 EVER 0x3002

SIMR 0x0000 MBXM 0xF000

SPER0 0xF000 SPER1 0xF000 SPER2 0xF000 SPER3 0xF000

SPER4 0xF000 SPER5 0xF000 SPER6 0xF000 SPER7 0xF000

MBXW0 0x0034 MBXW1 0x0034 MBXW2 0x0034 MBXW3 0x0034

MBXR0 0x0006 MBXR1 0x0006 MBXR2 0x0006 MBXR3 0x0006

MAC registers:

GCR: 0x4 GICR: 0x407 GMAC Status: 0x7 GBIC Status: 0xFE

MII registers of External GMAC:

Control Register (0x00): 0x140

Status Register (0x01): 0x14D

Auto Neg. Advt. Register (0x04): 0x1A0

Auto Neg. Partner Ability Reg (0x05): 0x0

TR_IPG_TIME Register (0x10): 0x7

PAUSE_TIME Register (0x11): 0x100

PAUSE_SA1 Register (0x13): 0x0

PAUSE_SA2 Register (0x14): 0x0

PAUSE_SA3 Register (0x15): 0x0

Pause Upper Threshold Reg. (0x19): 0xC00

Pause Lower Threshold Reg. (0x1A): 0x1000

TX Full Threshold Register (0x1B): 0x40

Memory Address Register (0x1C): 0xC006

Sync Status Register (0x1D): 0x40

Sys Status Register (0x1E): 0x7

Sys Control Register (0x1F): 0x3FDA

Auto Neg Ctrl Register (0xC004): 0x8008

Tx Phy Addr Register-GMAC (0xC005): 0x4FF

Rx Uinfo Registerter-GMAC (0xC006): 0xFF

Counters :

MR1 4123987649 MR2 0 MR3 66636001 MR4 19740879 MR5 7228754

MR6 7239820 MR7 19453016 MR8 95738 MR9 15431247 MR10 0

MR11 0 MR12 0 MR13 0 MR14 135825455 MR15 0

MR16 0 MR17 0 MR18 0 MR19 0 MR20 0

MR21 0

SR1 3075449862 SR2 172471375 SR3 0 SR4 0 SR5 0

MT1 1754265941 MT2 0 MT3 62593963 MT4 8142216 MT5 4818835

MT6 8116091 MT7 7146678 MT8 69320 MT9 79324386

ST1 0 ST2 0

MRXS 262238 MTXS 94 SRXS 4 STXS 0

1 REPLY
New Member

Re: output error in int g49 cat 2948g-l3

hi ,

can any one tell me why am i getting the error count at output error when the submition errors are showing zero counts.my network is not been effected.but y is this errors counters keeps increasing.

Can any one please explain.

79290942 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Thanks

134
Views
0
Helpful
1
Replies