Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

PA-FE-TX without handles

I have a PA-FE-TX that does not have any handles. I believe it came out of a CX-FEIP-2TX. The part # on the card is 73-1376-03 rev A0. I am trying to put it in a VIP2-40 that is in a 7505. When the router boots, I get traceback errors, and the card is not reconized in the VIP2-40. Can anyone tell me if I can use this card in anything but a CX-FEIP-2TX? Here is the errors I receive from the VIP2-40:

Nevada Error Interrupt Register 0x80

PCI bus 2 parity error

PMA error register = 0000000000000000

PCI master address = 0000000

PA Bay 0 Upstream PCI-PCI Bridge, Handle=0

Bridge chip is not DEC21050, DEC21052 or DEC21152, vendor/id=0x0

PA Bay 1 Upstream PCI-PCI Bridge, Handle=1

Bridge chip is not DEC21050, DEC21052 or DEC21152, vendor/id=0x0

Nested r4k_return_to_monitor call (2 times)

-Traceback= 0 60039C98 60038654 60023490 600B2F44 60195308 600B5AA8

Nested r4k_return_to_monitor call (3 times)

-Traceback= 0 600B303C 600B26F0 60195498 600990EC 60099458 600990EC 600B47D8

CYASIC Error Interrupt register 0x20000000

CYASIC Other Interrupt register 0x0

CYBUS Error register 0x0, PKT Bus Error register 0x0

System reloaded by a Bus Error exception

caller=0x600B62F8

System exception: sig=10, code=0x8, context=0x603690C0

$0 : 00000000, AT : 3400C000, v0 : 00000000, v1 : 00000045

a0 : 00000002, a1 : 602D0000, a2 : 00000000, a3 : 00000020

t0 : 00000053, t1 : 00000004, t2 : 00000000, t3 : FFFFFFFF

t4 : 00000000, t5 : 00001388, t6 : 00000000, t7 : 00000000

s0 : 00000000, s1 : 603690C0, s2 : 0000000A, s3 : 00000008

s4 : 00000000, s5 : 00000000, s6 : 60340000, s7 : FFFFFFFF

t8 : 34000000, t9 : 08008000, k0 : 603690C0, k1 : 00000018

gp : 60343320, sp : 602CFA08, s8 : FFFFFFFF, ra : 600B303C

EPC : 00000000, ErrorEPC : 80008618, SREG : 3400C003

Cause 00000008 (Code 0x2): TLB (load or instruction fetch) exception

-Traceback= 600B303C 600B26F0 60195498 600990EC 60099458 600990EC 600B47D8

--Boot log end--

1 REPLY
New Member

Re: PA-FE-TX without handles

I would suggest using the Hardware-Software compatibility matrix tool. I find that very usefull.

I have used the matrix with a 7513, VIP2 and port adapters, and it is very useful at identifying minimum levels of IOS and also, if the module is not listed, it might be an indication that it is not supported.

HTH

138
Views
0
Helpful
1
Replies