Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k

parity error

hi

i m getting the below mentioned error and my router goes in loop like rebootin continously.not coming to prompt none of the prompt.

%ERR-1-GT64120 (PCI-1): Fatal error, Parity error on master read

GT=0xB4000000, cause=0x00100000, mask=0x00D01D00, real_cause=0x00100000

bus_err_high=0x00000000, bus_err_low=0x31000000, addr_decode_err=0x00000470

r0 = FFFFFFFF r1 = FFFFFFFF r2 = 0 r3 = 61460000 r4 = 0

r5 = 60E036FC r6 = 0 r7 = 60E0370B r8 = 0 r9 = 61922AF4

r10 = 0 r11 = 0 r12 = 0 r13 = 40000000 r14 = FFFFFFFF

r15 = FFFFFFF8 r16 = 0 r17 = 0 r18 = 0 r19 = 619242A4

r20 = 0 r21 = 7 r22 = 0 r23 = 3E000000 r24 = 0

r25 = 61922A78 r26 = 0 r27 = 616AE6F0 r28 = 0 r29 = 61737528

r30 = 0 r31 = 61737524 r32 = FFFFFFFF r33 = FFFFFFFF r34 = FFFFFFFF

r35 = FFFFFFFF r36 = FFFFFFFF r37 = FFFFFFFF r38 = FFFFFFFF r39 = FFFFFFFF

r40 = FFFFFFFF r41 = FFFFFFFF r42 = FFFFFFFF r43 = FFFFFFFF r44 = FFFFFFFF

r45 = FFFFFFFF r46 = FFFFFFFF r47 = FFFFFFFF r48 = 0 r49 = 61737568

r50 = 0 r51 = 0 r52 = 0 r53 = 3041F001 r54 = 0

r55 = 100000 r56 = FFFFFFFF r57 = FFFFFFFF r58 = 0 r59 = 61A73258

r60 = FFFFFFFF r61 = FFFFFFFF r62 = 0 r63 = 6019CFC4

sreg = 3401E103 mdlo_hi = 0 mdlo = 1B207

mdhi_hi = 0 mdhi = 1 badvaddr_hi = FFFFFFFF

badvaddr = FFFFFFFF cause = FFFFFFFF epc_hi = 0

epc = 601A3320 err_epc_hi = FFFFFFFF err_epc = FFFFFFFF

%ERR-1-FATAL: Fatal error interrupt, reloading

err_stat=0x0

=== Flushing messages (01:31:32 UTC Mon Mar 1 1993) ===

Queued messages:

Unexpected exception, CPU signal 22, PC = 0x0

-Traceback= 0 0

$0 : 00000000, AT : 00000000, v0 : 00000000, v1 : 00000000

a0 : 00000000, a1 : 00000000, a2 : 00000000, a3 : 00000000

t0 : 00000000, t1 : 00000000, t2 : 00000000, t3 : 00000000

t4 : 00000000, t5 : 00000000, t6 : 00000000, t7 : 00000000

s0 : 00000000, s1 : 00000000, s2 : 00000000, s3 : 00000000

s4 : 00000000, s5 : 00000000, s6 : 00000000, s7 : 00000000

t8 : 00000000, t9 : 00000000, k0 : 00000000, k1 : 00000000

gp : 00000000, sp : 00000000, s8 : 00000000, ra : 00000000

EPC : 00000000, ErrorEPC : 00000000, SREG : 00000000

MDLO : 00000000, MDHI : 00000000, BadVaddr : 00000000

Cause 00000000 (Code 0x0): Interrupt exception

No fault history 0xFFFFFFFF. Need 11.1 (2) or higher ROM

Free space check for flash:crashinfo_19930301-013132 failed (-1/32768)

Free space check for slot0:crashinfo_19930301-013132 failed (-1/32768)

Free space check for slot1:crashinfo_19930301-013132 failed (-1/32768)

*** System received a System Error ***

signal= 0x16, code= 0x0, context= 0x618d16d0

PC = 0x6052eeec, Cause = 0x20, Status Reg = 0x34018002

C3660 processor with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

regds

prem

2 REPLIES
VIP Purple

Re: parity error

Hello,

this could be a memory hardware error, can you try to reseat the DRAM and Flash first (and if that doesn´t help replace it) and see if the error disappears ?

Regards,

Georg

New Member

Re: parity error

If this is a new install, definitily get the chassis and memory replaced first.

390
Views
0
Helpful
2
Replies
CreatePlease to create content