Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

PROB: Automatic Reboots?

I am using a Cisco 1600 Series with a 56k CSU/DSU addon card. Once I boot my router up, it asks me if I want to enter the initial configuration dialog. If I answer no, then it does the following:

Cisco Internetwork Operating System Software

IOS (tm) 1600 Software (C1600-Y-M), Version 12.0(14), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 31-Oct-00 16:18 by linda

Image text-base: 0x02005000, data-base: 0x0245EEAC

cisco 1601 (68360) processor (revision C) with 6144K/2048K bytes of memory.

Processor board ID 26409889, with hardware revision 00000006

Bridging software.

X.25 software, Version 3.0.0.

1 Ethernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

1 Serial(sync/async) network interface(s)

WIC with 56k 4-wire CSU/DSU

System/IO memory with parity disabled

8192K bytes of DRAM onboard

System running from RAM

7K bytes of non-volatile configuration memory.

4096K bytes of processor board PCMCIA flash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no

Would you like to terminate autoinstall? [yes]: yes

Press RETURN to get started!

00:00:11: SERVICE_MODULE(Serial1): self test finished: Passed

00:00:20: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up

00:00:20: %LINK-3-UPDOWN: Interface Serial0, changed state to down

00:00:20: %LINK-3-UPDOWN: Interface Serial1, changed state to up

00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta

te to up

00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state

to down

00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial

Router>1, changed state to up

00:00:44: %LINK-5-CHANGED: Interface Serial0, changed state to administratively

down

00:00:44: %LINK-5-CHANGED: Interface Ethernet0, changed state to administrativel

y down

00:00:44: %LINK-5-CHANGED: Interface Serial1, changed state to administratively

down

00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta

te to down

00:00:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state

to down

00:00:46: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) 1600 Software (C1600-Y-M), Version 12.0(14), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 31-Oct-00 16:18 by linda

Once I get the last few lines, it sits there until I hit enter. Once I hit enter I get the router> command line. It sure seems like the router shouldn't reboot itself like that, what am I doing wrong?

Thanks for the help!

--Mike

1 REPLY
New Member

Re: PROB: Automatic Reboots?

It seems normal as you look like starting it for the very first time. The IOS could not find any startup configuration. Either configure it from cli and try restarting it or use the config dialogue. Onec the startup configuration is saved it will work fine.

-Avi

181
Views
0
Helpful
1
Replies
CreatePlease to create content