10-25-2002 11:02 PM - edited 03-02-2019 02:24 AM
HELLO, My name is Moises I have two routers , i need to connect them.
1) First router the model is 10005 flash:c10k-p10-mz.120-22.S2.bin
2) Second router the model is 12406 flash:gsr-p-mz.120-22.S1.bin
They are connected to traves of link E3, my problem is the line protocol down in the Router 10005.
This is the configuration, router 10005
controller DSX3 1/0/1
dsx3mode e3
cablelength 10
description Back 12000
Serial1/0/1 is up, line protocol is down
Hardware is C10K E3/T3 Eight Port (E3 Mode)
Description: Prueba
Internet address is 192.16.10.9/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
This is the configuration, router 12406
interface Serial2/1
description Back 10005
ip address 192.168.10.10 255.255.255.252
no ip directed-broadcast
clock source internal
no cdp enable
Serial2/1 is up, line protocol is up
Hardware is Packet over E3
Description: Conexion Back-to-Back 10005 Enlace 2
Internet address is 192.168.10.10/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Thanks .
10-26-2002 09:44 PM
HELLO, My name is Moises I have two routers , i need to connect them.
1) First router the model is 10005 flash:c10k-p10-mz.120-22.S2.bin
2) Second router the model is 12406 flash:gsr-p-mz.120-22.S1.bin
They are connected to traves of link E3, my problem is the line protocol down in the Router 10005.
This is the configuration, router 10005
controller DSX3 1/0/1
dsx3mode e3
cablelength 10
description Back 12000
Serial1/0/1 is up, line protocol is down
Hardware is C10K E3/T3 Eight Port (E3 Mode)
Description: Prueba
Internet address is 192.16.10.9/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
This is the configuration, router 12406
interface Serial2/1
description Back 10005
ip address 192.168.10.10 255.255.255.252
no ip directed-broadcast
clock source internal
no cdp enable
Serial2/1 is up, line protocol is up
Hardware is Packet over E3
Description: Conexion Back-to-Back 10005 Enlace 2
Internet address is 192.168.10.10/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Thanks .
10-27-2002 08:25 AM
HELLO, My name is Moises I have two routers , i need to connect them.
1) First router the model is 10005 flash:c10k-p10-mz.120-22.S2.bin
2) Second router the model is 12406 flash:gsr-p-mz.120-22.S1.bin
They are connected to traves of link E3, my problem is the line protocol down in the Router 10005.
This is the configuration, router 10005
controller DSX3 1/0/1
dsx3mode e3
cablelength 10
description Back 12000
Serial1/0/1 is up, line protocol is down
Hardware is C10K E3/T3 Eight Port (E3 Mode)
Description: Prueba
Internet address is 192.16.10.9/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
This is the configuration, router 12406
interface Serial2/1
description Back 10005
ip address 192.168.10.10 255.255.255.252
no ip directed-broadcast
clock source internal
no cdp enable
Serial2/1 is up, line protocol is up
Hardware is Packet over E3
Description: Conexion Back-to-Back 10005 Enlace 2
Internet address is 192.168.10.10/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Thanks .
10-28-2002 11:54 PM
HELLO, My name is Moises I have two routers , i need to connect them.
1) First router the model is 10005 flash:c10k-p10-mz.120-22.S2.bin
2) Second router the model is 12406 flash:gsr-p-mz.120-22.S1.bin
They are connected to traves of link E3, my problem is the line protocol down in the Router 10005.
This is the configuration, router 10005
controller DSX3 1/0/1
dsx3mode e3
cablelength 10
description Back 12000
Serial1/0/1 is up, line protocol is down
Hardware is C10K E3/T3 Eight Port (E3 Mode)
Description: Prueba
Internet address is 192.16.10.9/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
This is the configuration, router 12406
interface Serial2/1
description Back 10005
ip address 192.168.10.10 255.255.255.252
no ip directed-broadcast
clock source internal
no cdp enable
Serial2/1 is up, line protocol is up
Hardware is Packet over E3
Description: Conexion Back-to-Back 10005 Enlace 2
Internet address is 192.168.10.10/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Thanks .
11-15-2002 01:32 PM
HELLO, My name is Moises I have two routers , i need to connect them.
1) First router the model is 10005 flash:c10k-p10-mz.120-22.S2.bin
2) Second router the model is 12406 flash:gsr-p-mz.120-22.S1.bin
They are connected to traves of link E3, my problem is the line protocol down in the Router 10005.
This is the configuration, router 10005
controller DSX3 1/0/1
dsx3mode e3
cablelength 10
description Back 12000
Serial1/0/1 is up, line protocol is down
Hardware is C10K E3/T3 Eight Port (E3 Mode)
Description: Prueba
Internet address is 192.16.10.9/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
This is the configuration, router 12406
interface Serial2/1
description Back 10005
ip address 192.168.10.10 255.255.255.252
no ip directed-broadcast
clock source internal
no cdp enable
Serial2/1 is up, line protocol is up
Hardware is Packet over E3
Description: Conexion Back-to-Back 10005 Enlace 2
Internet address is 192.168.10.10/30
MTU 4470 bytes, BW 34010 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide