Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

problem of dial from aux,please help!!!

router2600---aux----modem(datacraft 3296H)

cisco2600#sh int async 65

Async65 is up (spoofing), line protocol is up (spoofing)

¡£¡£¡£

cisco2600#sh line 65

Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

* 65 AUX 38400/38400 - inout - - - 0 0 0/15049 -

Ready

Line 65, Location: "", Type: ""

Length: 24 lines, Width: 80 columns

Baud rate (TX/RX) is 38400/38400, no parity, 1 stopbits, 8 databits

Status: Ready, Active, No Exit Banner, CTS Raised, Modem Signals Polled

Capabilities: Modem Callout, Modem RI is CD, Modem Autoconfigure

Modem state: Ready

Modem hardware state: CTS* DSR* DTR RTS

TTY NUMBER 65

Parity Error = 0 Framing Error = 45 Receive Error = 45 Overrun = 0

Outcount = 0 totalout = 34024 incount = 0 totalin = 24819

Special Chars: Escape Hold Stop Start Disconnect Activation

^^x none - - none

Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch

never never none not set

Idle Session Disconnect Warning

never

Login-sequence User Response

00:00:30

Autoselect Initial Wait

not set

Modem type is MY_MODEM.

Session limit is not set.

Time since activation: 00:01:47

Editing is enabled.

History is enabled, history size is 10.

DNS resolution in show commands is enabled

Full user help is disabled

Allowed transports are pad v120 telnet rlogin. Preferred is telnet.

No output characters are padded

No special data dispatching characters

cisco2600#

cisco2600#sh debug

General OS:

Modem control/process activation debugging is on

Dial on demand:

Dial on demand events debugging is on

cisco2600#ping 1.1.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:

00:12:56: As65 DDR: Dialing cause ip (s=90.1.1.1, d=1.1.1.1)

00:12:56: As65 DDR: Attempting to dial 852

00:12:56: CHAT65: Attempting async line dialer script

00:12:56: CHAT65: dial attempt to 852 and line is in use

00:12:56: As65 DDR: Unable to dial 852......

Success rate is 0 percent (0/5)

cisco2600#clear line 65

[confirm]y [OK]

cisco2600#

00:13:26: TTY65: Line reset by "Exec"

00:13:26: TTY65: Modem: (unknown)->HANGUP

00:13:26: TTY65: no timer type 0 to destroy

00:13:26: TTY65: destroy timer type 1

00:13:26: TTY65: no timer type 3 to destroy

00:13:26: TTY65: no timer type 4 to destroy

00:13:26: TTY65: no timer type 2 to destroy

00:13:27: TTY65: dropping DTR, hanging up

00:13:27: TTY65: Set DTR to 0

00:13:27: tty65: Modem: HANGUP->IDLEclear line 6

00:13:29: TTY65: restoring DTR

00:13:29: TTY65: Set DTR to 1

00:13:30: TTY65: DSR came up

00:13:30: tty65: Modem: IDLE->(unknown)

00:13:30: TTY65: EXEC creation

00:13:30: TTY65: create timer type 1,

cisco2600#

cisco2600#ping 1.1.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:

00:13:35: As65 DDR: Dialing cause ip (s=90.1.1.1, d=1.1.1.1)

00:13:35: As65 DDR: Attempting to dial 852

00:13:35: CHAT65: Attempting async line dialer script

00:13:35: CHAT65: dial attempt to 852 and line is in use

00:13:35: As65 DDR: Unable to dial 852......

Success rate is 0 percent (0/5)

cisco2600#

00:13:50: As65 DDR: re-enable timeout

router config is:

modemcap entry MY_MODEM:MSC=&F1S0=1

interface Async65

ip address 90.1.1.1 255.255.255.0

encapsulation ppp

dialer in-band

dialer idle-timeout 900

dialer string 852

dialer-group 1

!

ip route 0.0.0.0 0.0.0.0 Async65

line aux 0

exec-timeout 0 0

modem InOut

modem autoconfigure my_modem

transport input all

stopbits 1

speed 38400

1 REPLY
Community Member

Re: problem of dial from aux,please help!!!

I found DDR will work if I ping 1.1.1.1 at middle of "clear line 65",I don't know why.

cisco2600#clear line 65

[confirm]y [OK]

cisco2600#clear line 65

00:28:31: TTY65: Line reset by "Exec"

00:28:31: TTY65: Modem: (unknown)->HANGUP

00:28:31: TTY65: no timer type 0 to destroy

00:28:31: TTY65: no timer type 1 to destroy

00:28:31: TTY65: no timer type 3 to destroy

00:28:31: TTY65: no timer type 4 to destroy

00:28:31: TTY65: no timer type 2 to destroy

00:28:31: TTY65: dropping DTR, hanging up

00:28:31: TTY65: Set DTR to 0

00:28:31: tty65: Modem: HANGUP->(unknown)

00:28:31: TTY65: cleanup pending.

ping 1.1.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:

00:28:33: TTY65: restoring DTR

00:28:33: TTY65: Set DTR to 1

00:28:34: As65 DDR: Dialing cause ip (s=90.1.1.1, d=1.1.1.1)

00:28:34: As65 DDR: Attempting to dial 293

00:28:34: CHAT65: Attempting async line dialer script

00:28:34: CHAT65: no matching chat script found for 293

00:28:34: CHAT65: Dialing using Modem script: d0efault-d0ials0cript & System scr

ipt: none

00:28:34: CHAT65: process started

00:28:34: CHAT65: Asserting DTR

00:28:34: TTY65: Set DTR to 1

00:28:34: CHAT65: Chat script d0efault-d0ials0cript started.....

Success rate is 0 percent (0/5)

cisco2600#

132
Views
0
Helpful
1
Replies
CreatePlease to create content