Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

question about debug condition interface command

as i konw that debug condition interface command can analyse one specific interface.

when i specified just one interface serial 3/2:5 (it is channelized with x25 line)

but bebug result shows all of other interfaces (se 2/0)

how can i see just one specified interface serial 3/2:5

KCB_CEX_XRT_1#show debugging

Condition 1: interface Se3/2:5 (1 flags triggered)

Flags: Se3/2:5

KCB_CEX_XRT_1#debug x25

X.25 packet debugging is on

KCB_CEX_XRT_1#

Sep 17 01:11:12.395: Serial3/2:5: X.25 I D1 Data (3) 8 lci 1 PS 0 PR 0

Sep 17 01:11:12.395: Serial2/0: X.25 O D1 Data (3) 8 lci 11 PS 0 PR 0

Sep 17 01:11:12.395: Serial3/2:5: X.25 I D1 Data (3) 8 lci 2 PS 0 PR 0

Sep 17 01:11:12.395: Serial2/0: X.25 O D1 Data (3) 8 lci 12 PS 0 PR 0

Sep 17 01:11:12.395: Serial2/0: X.25 I D1 RR (3) 8 lci 11 PR 1

Sep 17 01:11:12.395: Serial3/2:5: X.25 O D1 RR (3) 8 lci 1 PR 1

Sep 17 01:11:12.395: Serial2/0: X.25 I D1 RR (3) 8 lci 12 PR 1

Sep 17 01:11:12.395: Serial3/2:5: X.25 O D1 RR (3) 8 lci 2 PR 1

Sep 17 01:11:12.399: Serial3/2:5: X.25 I D1 Data (3) 8 lci 3 PS 0 PR 0

Sep 17 01:11:12.399: Serial2/0: X.25 O D1 Data (3) 8 lci 13 PS 0 PR 0

Sep 17 01:11:12.399: Serial2/0: X.25 I D1 RR (3) 8 lci 13 PR 1

Sep 17 01:11:12.399: Serial3/2:5: X.25 O D1 RR (3) 8 lci 3 PR 1

Sep 17 01:11:12.399: Serial2/0: X.25 I D1 Reset (5) 8 lci 11

Sep 17 01:11:12.399: Cause 0, Diag 0 (DTE originated/No additional information)

Sep 17 01:11:12.399: Serial2/0: X.25 O D3 Reset Confirm (3) 8 lci 11

Sep 17 01:11:12.399: Serial3/2:5: X.25 O D1 Reset (5) 8 lci 1

Sep 17 01:11:12.399: Cause 0, Diag 0 (DTE originated/No additional information)

Sep 17 01:11:12.407: Serial2/0: X.25 I D1 Reset (5) 8 lci 12

Sep 17 01:11:12.407: Cause 0, Diag 0 (DTE originated/No additional information)

Sep 17 01:11:12.407: Serial2/0: X.25 O D3 Reset Confirm (3) 8 lci 12

Sep 17 01:11:12.407: Serial3/2:5: X.25 O D1 Reset (5) 8 lci 2

Sep 17 01:11:12.407: Cause 0, Diag 0 (DTE originated/No additional information)

Sep 17 01:11:12.407: Serial2/0: X.25 I D1 Reset (5) 8 lci 13

Sep 17 01:11:12.407: Cause 0, Diag 0 (DTE originated/No additional information)

Sep 17 01:11:12.407: Serial2/0: X.25 O D3 Reset Confirm (3) 8 lci 13

Sep 17 01:11:12.407: Serial3/2:5: X.25 O D1 Reset (5) 8 lci 3

Sep 17 01:11:12.407: Cause 0, Diag 0 (DTE originated/No additional information)

Sep 17 01:11:12.407: Serial3/2:5: X.25 I D2 Reset Confirm (3) 8 lci 1

KCB_CEX_XRT_1#

Sep 17 01:11:12.411: Serial3/2:5: X.25 I D2 Reset Confirm (3) 8 lci 2

Sep 17 01:11:12.411: Serial3/2:5: X.25 I D2 Reset Confirm (3) 8 lci 3

KCB_CEX_XRT_1#no debug all

Port Statistics for unclassified packets is not turned on.

thx in advancd

1 REPLY
Bronze

Re: question about debug condition interface command

Hi,

Try using this command

router#debug x25 interface serial 3/2:5

HTH

Thanks

Raj

244
Views
0
Helpful
1
Replies
CreatePlease login to create content