Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

redundant supervisor in Stanby Cold state

We had a Sup 2T throw a parity error, TAC RMA'd a replacement SUP2T. I ensured that the same IOS version was on the replacement. Inserted the card and in Show Mod it shows pass and ok however when I look at the show redundancy I am seeing the replacement SUP i as Standby COLD. when I look at the show redundancy states I see the following: 

Redundancy Mode (Operational) = rpr    Reason: Software mismat

when I look at the Bootvar I see the following:

BOOT variable = bootdisk:s2t54-advipservicesk9-mz.SPA.151-1.SY1.bin,1;
CONFIG_FILE variable = 
BOOTLDR variable = 
Configuration register is 0x2102

Standby BOOT variable = bootdisk:s2t54-advipservicesk9-mz.SPA.151-1.SY1.bin,1;
Standby CONFIG_FILE variable = 
Standby BOOTLDR variable = 
Standby Configuration register is 0x2102 

 

Any Ideas ?

  • Other Network Infrastructure Subjects
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

That all looks good. I notice

That all looks good. I notice your operational redundancy mode is RPR. Is that the configured mode (normally SSO would be the configured mode).

Does "show module" recognize the replaced card properly? Have you tried reloading the standby supervisor ("redundancy reload peer")? I'd do that while checking if any console or syslog messages are generated during that process to give more troubleshooting clues.

3 REPLIES
Hall of Fame Super Silver

Do you perhaps have licensing

Do you perhaps have licensing (e.g., MacSEC) on the primary that isn't matched on the secondary?

"show license all"

"show license feature"

New Member

Here is the output from these

Here is the output from these two commands 

show license all
License Store: Primary License Storage
License Store: Evaluation License Storage
StoreIndex: 0   Feature: TEST_FEATURE_1                    Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 4  weeks 2  days 
            Evaluation period left: 4  weeks 2  days 
        Lock type: Non Node locked
        Vendor info: 
        License Addition: Additive
        License Generation version: 0x8100000
        License Count: Non-Counted
        License Priority: None
StoreIndex: 1   Feature: TEST_FEATURE_2                    Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 1  hour  0  minute  
            Evaluation period left: 1  hour  0  minute  
        Lock type: Non Node locked
        Vendor info: 
        License Addition: Additive
        License Generation version: 0x8100000
        License Count: Non-Counted
        License Priority: None

show license feature
Feature name             Enforcement  Evaluation  Subscription   Enabled
MACSec_Encryption        yes          no          no             no   
CTS                      yes          no          no             no   
TEST_FEATURE_1           yes          yes         no             no   
TEST_FEATURE_2           yes          yes         no             no   

 

Hall of Fame Super Silver

That all looks good. I notice

That all looks good. I notice your operational redundancy mode is RPR. Is that the configured mode (normally SSO would be the configured mode).

Does "show module" recognize the replaced card properly? Have you tried reloading the standby supervisor ("redundancy reload peer")? I'd do that while checking if any console or syslog messages are generated during that process to give more troubleshooting clues.

228
Views
0
Helpful
3
Replies
This widget could not be displayed.