Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

reset problem on 6509 catalyst switch

Reset is require sometimes on WS-X6K-SUP2-2GE what could be the possible reasons.....

sh ver :-----

WS-C6509 Software, Version NmpSW: 6.1(1d)

Copyright (c) 1995-2001 by Cisco Systems

NMP S/W compiled on Jan 10 2001, 20:40:46

System Bootstrap Version: 6.1(3)

Hardware Version: 2.0 Model: WS-C6509 Serial #: SCA052701R0

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP2-2GE SAD052003KT Hw : 2.2

Fw : 6.1(3)

Fw1: 6.1(3)

Sw : 6.1(1d)

Sw1: 6.1(1d)

WS-F6K-PFC2 SAD052103DK Hw : 1.4

2 2 WS-X6K-SUP2-2GE SAD052202BY Hw : 2.2

Fw : 6.1(3)

Fw1: 6.1(3)

Sw : 6.1(1d)

Sw1: 6.1(1d)

WS-F6K-PFC2 SAD052304GE Hw : 1.4

3 8 WS-X6408A-GBIC SAL05268Y6V Hw : 2.0

Fw : 5.4(2)

Sw : 6.1(1d)

4 48 WS-X6348-RJ-45 SAL05268YUJ Hw : 3.1

Fw : 5.4(2)

Sw : 6.1(1d)

5 2 WS-X6380-NAM SAD052500WL Hw : 1.3

Fw : 4B4LZ0XA

Fw1: 5.4(2)

Sw : 1.1(1a)

Sw1: 6.1(1d)

6 2 WS-X6381-IDS SAD052504MS Hw : 1.1

Fw : 4B4LZ0XA

Sw : 2.5(1)S2a

7 2 WS-X6101-OC12-MMF SAD0521049C Hw : 1.3

Fw : 12.1(5c)E10,

Sw : 12.1(5c)E10,

15 1 WS-F6K-MSFC2 SAD05080SHR Hw : 1.2

Fw : 12.1(4)E1

Sw : 12.1(4)E1

16 1 WS-F6K-MSFC2 SAD051100RJ Hw : 1.2

Fw : 12.1(4)E1

Sw : 12.1(4)E1

NVRAM DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 130944K 57131K 73813K 32768K 6613K 26155K 512K 287K 225K

Uptime is 0 day, 4 hours, 26 minutes

sh log:---

Network Management Processor (ACTIVE NMP) Log:

Reset count: 47

Re-boot History: Jun 27 2002 11:54:41 0, Jun 25 2002 16:14:16 0

Jun 24 2002 09:55:22 0, Jun 18 2002 12:15:50 0

Jun 18 2002 12:08:51 0, Jun 13 2002 16:19:06 0

Jun 13 2002 16:12:51 0, Jun 12 2002 09:51:55 0

Jun 10 2002 17:20:48 0, Jun 10 2002 15:26:02 0

Bootrom Checksum Failures: 0 UART Failures: 0

Flash Checksum Failures: 0 Flash Program Failures: 0

Power Supply 1 Failures: 0 Power Supply 2 Failures: 0

Swapped to CLKA: 0 Swapped to CLKB: 0

Swapped to Processor 1: 0 Swapped to Processor 2: 0

DRAM Failures: 0

Exceptions: 0

Loaded NMP version: 6.1(1d)

Reload same NMP version count: 48

EOBC Exceptions/Hang: 0

Heap Memory Log:

Corrupted Block = none

NVRAM log:

01. 1/9/2002,12:26:56: RxSBIF_SEQ_NUM_ERROR:slot=1, pinnacleMask=0X1, errSeqNum=0,source Index=0X0, errorType=0X1

Network Management Processor (STANDBY NMP) Log:

Reset count: 47

Re-boot History: Jun 27 2002 11:54:41 0, Jun 25 2002 16:14:15 0

Jun 24 2002 09:55:21 0, Jun 18 2002 12:15:49 0

Jun 18 2002 12:08:52 0, Jun 13 2002 16:19:05 0

Jun 13 2002 16:12:52 0, Jun 12 2002 09:51:55 0

Jun 10 2002 17:20:48 0, Jun 10 2002 15:26:01 0

Bootrom Checksum Failures: 0 UART Failures: 0

Flash Checksum Failures: 0 Flash Program Failures: 0

Power Supply 1 Failures: 0 Power Supply 2 Failures: 0

Swapped to CLKA: 0 Swapped to CLKB: 0

Swapped to Processor 1: 0 Swapped to Processor 2: 0

DRAM Failures: 0

Exceptions: 0

Loaded NMP version: 6.1(1d)

Reload same NMP version count: 48

EOBC Exceptions/Hang: 0

Heap Memory Log:

Corrupted Block = none

NVRAM log:

01. 7/17/2001,15:18:33: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

02. 1/9/2002,12:04:23: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

03. 1/9/2002,12:23:42: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

04. 1/12/2002,21:55:07: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

05. 1/23/2002,12:32:30: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

06. 1/25/2002,14:03:52: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

07. 1/25/2002,17:48:56: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

08. 2/15/2002,16:17:11: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

09. 3/6/2002,13:14:20: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

10. 3/8/2002,10:23:59: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

11. 3/27/2002,11:08:11: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

12. 5/7/2002,11:57:00: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

13. 5/8/2002,19:07:36: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

14. 5/14/2002,18:07:36: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

15. 5/17/2002,19:02:23: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

16. 5/18/2002,19:54:51: ha_swover_sync_status:static-db:1, dyn-db:0 (0-invalid, 1-valid)

17. 5/24/2002,06:36:00: ha_swover_sync_status:static-db:1, dyn-db:0

1 REPLY
Cisco Employee

Re: reset problem on 6509 catalyst switch

You are running a very old CAT OS and MSFC IOS you are running is defferred. I suggest that you upgrade CAT OS to 6.3(7) and MSFC2 to 12.1(8b)E11 and it should alleviate most of your issues.

342
Views
0
Helpful
1
Replies