Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Routing with 6509 ...HELP

I want to create multiples Vlans with this switch.My 6509 will be the core. My problem is how can I configure the interfaces to routing. When I start session 15 in enable mode I only get Vlan 1 when I use the show interface command. The must complicated part is that I can't get a physical interface an sub-interface to assigne my Ip address and mask. I need to know the commands I can use to fix this problem. How to configure VTP between router and switch?

Wich command can I use to configure inter-Vlans routing?

This is my output when using show modules command and some more specificacions.

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

2 2 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes standby

16 2 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok

4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok

5 5 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok

6 6 16 1000BaseSX Ethernet WS-X6416-GE-MT no ok

7 7 16 1000BaseSX Ethernet WS-X6416-GE-MT no ok

8 8 8 1000BaseX Ethernet WS-X6408A-GBIC no ok

9 9 16 1000BaseX Ethernet WS-X6416-GBIC no ok

WS-C6509 Software, Version NmpSW: 5.5(1)

Copyright (c) 1995-2000 by Cisco Systems

NMP S/W compiled on Jun 8 2000, 21:09:45

System Bootstrap Version: 5.3(1)

Hardware Version: 2.0 Model: WS-C6509 Serial #: SCA043801E1

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP1A-2GE SAD05040EBR Hw : 7.0

Fw : 5.3(1)

Fw1: 5.4(2)

Sw : 5.5(1)

Sw1: 5.5(1)

L3 Switching Engine SAD0504082D Hw : 1.1

2 2 WS-X6K-SUP1A-2GE SAD05030CD9 Hw : 7.0

Fw : 5.3(1)

Fw1: 5.4(2)

Sw : 5.5(1)

Sw1: 5.5(1)

L3 Switching Engine SAD05030BEJ Hw : 1.1

3 48 WS-X6348-RJ-45 SAL045047A6 Hw : 1.4

Fw : 5.4(2)

Sw : 5.5(1)

4 48 WS-X6348-RJ-45 SAL044946PP Hw : 1.4

Fw : 5.4(2)

Sw : 5.5(1)

5 48 WS-X6348-RJ-45 SAL04504779 Hw : 1.4

Fw : 5.4(2)

Sw : 5.5(1)

6 16 WS-X6416-GE-MT SAD04400CUY Hw : 1.1

Fw : 5.4(2)

Sw : 5.5(1)

7 16 WS-X6416-GE-MT SAL0537BGRZ Hw : 1.3

Fw : 5.4(2)

Sw : 5.5(1)

8 8 WS-X6408A-GBIC SAD0449070B Hw : 1.3

Fw : 5.4(2)

Sw : 5.5(1)

9 16 WS-X6416-GBIC SAL0607J10E Hw : 2.0

Fw : 5.4(2)

Sw : 5.5(1)

15 1 WS-F6K-MSFC2 SAD0504029B Hw : 1.2

Fw : 12.1(2)E,

Sw : 12.1(2)E,

16 1 WS-F6K-MSFC2 SAD05030NSM Hw : 1.2

Fw : 12.1(2)E,

Sw : 12.1(2)E,

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 65408K 38722K 26686K 16384K 6925K 9459K 512K 288K 224K

Uptime is 212 days, 15 hours, 21 minutes

set boot system flash bootflash:cat6000-sup.5-5-1.bin

1 REPLY
Silver

Re: Routing with 6509 ...HELP

Check the website below. I think this is what you are looking for.

http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_guide_chapter09186a008007f29a.html

Hope this helps.

Steve

87
Views
0
Helpful
1
Replies