Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Cisco Employee

Show command to identify port adapter

Hi All,

I have a 7200 with three slot already full with some port adapter.

I have to order a new PA with four serial interfaces. I am quite sure that the module alredy implemented in the router is PA-4T+.

I need to confirm this to order another module of the same type.

I have no physical access to the router, but I can telnet in.

I tried with show diag and I had:

------------------ show diag ------------------

Slot 0:

Fast-ethernet on C7200 I/O card with MII or RJ45 port adapter, 1 port

Port adapter is analyzed

Port adapter insertion time 6w4d ago

Hardware revision 1.3 Board revision B0

Serial number 14305041 Part number 73-2956-02

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 83 01 03 00 DA 47 11 49 0B 8C 02 00 00 00 00

0x30: 58 00 00 00 99 07 26 00 00 FF FF FF FF FF FF FF

Slot 1:

Ethernet port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time 6w4d ago

Hardware revision 1.13 Board revision B0

Serial number 10953791 Part number 73-1556-07

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 02 01 0D 00 A7 24 3F 49 06 14 07 00 00 00 00

0x30: 58 00 00 00 98 12 07 00 FF FF FF FF FF FF FF FF

Slot 2:

Mx serial port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time 6w4d ago

Hardware revision 1.10 Board revision A0

Serial number 8528386 Part number 73-1577-05

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 0C 01 0A 00 82 22 02 49 06 29 05 00 00 00 00

0x30: 50 00 00 00 98 07 30 00 FF FF FF FF FF FF FF FF

------------------ show c7200 ------------------

C7200 Network IO Interrupt Throttling:

throttle count=0, timer count=0

active=0, configured=0

netint usec=4000, netint mask usec=200

C7200 Midplane EEPROM:

Hardware revision 1.3 Board revision M0

Serial number 15375662 Part number 73-1539-03

Test history 0x0 RMA number 00-00-00

MAC=00d0.ffb4.4000, MAC Size=1024

EEPROM format version 1, Model=0x6

EEPROM contents (hex):

0x20: 01 06 01 03 00 EA 9D 2E 49 06 03 03 00 D0 FF B4

0x30: 40 00 04 00 00 00 00 00 4C 84 02 B0 FF FF 00 FF

C7200 CPU EEPROM:

Hardware revision 2.4 Board revision D0

Serial number 11512903 Part number 73-2441-03

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 69 02 04 00 AF AC 47 49 09 89 03 00 00 00 00

0x30: 68 00 00 00 99 06 27 00 FF FF FF FF FF FF FF FF

How can I understand that the actual module in slot 2 is really the PA-4T+?

From the part number?

How can I link it with the order name/number?

Any help appreciated.

Matteo

Thanks

2 REPLIES
Community Member

Re: Show command to identify port adapter

If you provide Cisco with the serial number and Part number as shown on your output of the show diag command, they should be able to tell you exactly what item number is.

Your output tells you whats in slot 2 and it does appear you have a 4 port serial adapter in that slot.

Hope this helps.

Community Member

Re: Show command to identify port adapter

For part number 73-1577, I'm sure that it's a PA4T+

Reguards

130
Views
0
Helpful
2
Replies
CreatePlease to create content