Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

SupVisIII E2 EARL not active

Hallo,

I have a new SupVisIII with NFFC (WS-X5530-E1). sh mod shows me EARL Status , but 'U' unknown, for all options.

Is there a hardware errors or somethings else ?

Below is sho mod and sho test screnn shot.

Thanks

Ruedi

Console> (enable) sh test 1

Diagnostic mode: complete (mode at next reset: complete)

Module 1 : 0-port Supervisor III

Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)

ROM: . Flash-EEPROM: . Ser-EEPROM: . NVRAM: . MCP Comm: .

EARL II Status :

DisableIndexLearnTest: U

DontLearnTest: U

DisableNewLearnTest: U

ConditionalLearnTest: U

MonitorColorFloodTest: U

EarlTrapTest: U

StaticMacAndTypeTest: U

BadDvlanTest: U

BadBpduTest: U

IndexMatchTest: U

ProtocolTypeTest: U

IgmpTest: U

SourceMissTest: U

SourceModifiedTest: U

ArpaToArpaShortcutTest: U

ArpaToSnapShortcutTest: U

SnapToArpaShortcutTest: U

SnapToSnapShortcutTest: U

SoftwareShortcutTest: U

MulticastExpansionTest: U

DontShortcutTest: U

ShortcutTableFullTest: U

Line Card Diag Status for Module 1 (. = Pass, F = Fail, N = N/A)

CPU : . Sprom : . Bootcsum : . Archsum : .

RAM : . LTL : . CBL : N DPRAM : . SAMBA : N

Saints : . Pkt Bufs : . Repeater : N FLASH : .

Phoenix : . TrafficMeter: . UplinkSprom : . PhoenixSprom: .

SAINT/SAGE Status :

PHOENIX Port Status :

Ports 9 17 18 19 20 21 22

INBAND A->B B->A B->C C->B A->C C->A

------------------------------------------

. . . . . . .

Packet Buffer Status :

PHOENIX Packet Buffer Status :

Ports INBAND A<->B B<->C A<->C

------------------------------

. . . .

Loopback Status [Reported by Module 1] :

Ports 1 2 9

--------------

U U .

Console> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 0 Supervisor III WS-X5530 yes ok

4 4 24 10/100BaseTX Ethernet WS-X5224 no ok

5 5 24 10/100BaseTX Ethernet WS-X5224 no ok

Mod Module-Name Serial-Num

--- ------------------- --------------------

1 00011471714

4 00012139314

5 00010057520

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-d0-06-53-00-00 to 00-d0-06-53-03-ff 2.5 5.1(2) 5.5(9)

4 00-50-53-c5-13-f0 to 00-50-53-c5-14-07 1.5 3.1(1) 5.5(9)

5 00-10-7b-b9-78-08 to 00-10-7b-b9-78-1f 1.4 3.1(1) 5.5(9)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- -------- --------- ---------- ------

1 NFFC WS-F5521 0011474995 1.1

Console> (enable)

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: SupVisIII E2 EARL not active

I believe this is because your Supervisor Engine does not have any uplink modules. I tested in the lab here and found same results

2 REPLIES
Cisco Employee

Re: SupVisIII E2 EARL not active

I believe this is because your Supervisor Engine does not have any uplink modules. I tested in the lab here and found same results

New Member

Re: SupVisIII E2 EARL not active

Hello, Thanks for response. I found same reason on friday afternoon. But there was no time to send you this information on friday.

Thanks for help

Kind regards

Ruedi

91
Views
0
Helpful
2
Replies
CreatePlease to create content