Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Swapping a WS-SUP720-3B supervisor board in Catalyst 6509-E

Hello,

I was hoping for some insight.  I currently have two switches.  A Catalyst 6509-E and a Catalyst 6503.  Both switches are using the WS-SUP720-3B supervisor board.  The Catalyst 6503 is currently just a spare and it is not being used anymore.  I was wondering what the procedure would be to remove the SUP720-3B board out of the Catalyst 6509-E and replace it with the supervisor board from the Catalyst 6503.  Currently they are running 2 different configs.  Eventually I am wanting to install the spare supervisor board into the Catalyst 6509-E as a redundant board but I need to upgrade the software on it first I believe.  I am just currently looking at a solution in case the Supervisor Board should fail in the Catalyst 6509-E and I would need to replace it with the one from the Catalyst 6503.  I have attached my show module output from both switches.  The top one is my Catalyst 6509-E and the bottom one is my Catalyst 6503.  Thank you.   

Catalyst 6509-E              

Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAL13410K8H
  4   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1010F9FH
  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAD104204PV
  7   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1246AC2B
  8   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1248BD0Z

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  0023.eb12.7080 to 0023.eb12.7083   3.0   12.2(14r)S5  12.2(18)SXF1 Ok
  4  0017.5937.1c30 to 0017.5937.1c5f   2.3   12.2(14r)S5  12.2(18)SXF1 Ok
  5  000f.8f3a.83bc to 000f.8f3a.83bf   5.2   8.5(4)       12.2(18)SXF1 Ok
  7  0023.0456.4c68 to 0023.0456.4c97   3.0   12.2(18r)S1  12.2(18)SXF1 Ok
  8  0021.a0ca.c618 to 0021.a0ca.c647   3.0   12.2(18r)S1  12.2(18)SXF1 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  1  Centralized Forwarding Card WS-F6700-CFC       SAL1330UMZ0  4.1    Ok
  4  Centralized Forwarding Card WS-F6700-CFC       SAD103908UD  3.0    Ok
  5  Policy Feature Card 3       WS-F6K-PFC3B       SAD104208A0  2.3    Ok
  5  MSFC3 Daughterboard         WS-SUP720          SAD0951045E  2.5    Ok
  7  Centralized Forwarding Card WS-F6700-CFC       SAL1022Q66R  2.0    Ok
  8  Centralized Forwarding Card WS-F6700-CFC       SAL12361Z0A  4.1    Ok

Catalyst 6503

Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1229XJJF
  3   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1231YZG6

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  000a.b86d.76b8 to 000a.b86d.76bb   5.6   8.5(2)       12.2(33)SXH3 Ok
  3  0022.55f8.23b4 to 0022.55f8.23e3   3.0   12.2(18r)S1  12.2(33)SXH3 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  1  Policy Feature Card 3       WS-F6K-PFC3B       SAL1226V5PR  2.3    Ok
  1  MSFC3 Daughterboard         WS-SUP720          SAL1229XDLP  3.1    Ok
  3  Centralized Forwarding Card WS-F6700-CFC       SAL1228X9BN  4.1    Ok

536
Views
0
Helpful
0
Replies
CreatePlease login to create content