Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Switch not working

Hi all,

I am facing a problem with Cisco Catalyst 3550 switch

after booting the switch gives a message

!!! WARNING: The switch is not usable !!!

the post test results are as below

Initializing flashfs...

flashfs[1]: 350 files, 5 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15998976

flashfs[1]: Bytes used: 5008896

flashfs[1]: Bytes available: 10990080

flashfs[1]: flashfs fsck took 8 seconds.

flashfs[1]: Initialization complete.

...done Initializing flashfs.

POST: CPU Buffer Tests : Begin

POST: CPU Buffer Tests : End, Status Passed

POST: CPU Interface Tests : Begin

POST: CPU Interface Tests : End, Status Passed

POST: Switch Core Tests : Begin

POST: Switch Core Tests : End, Status Passed

POST: CPU Interface 2nd Stage Tests : Begin

POST: CPU Interface 2nd Stage Tests : End, Status Passed

POST: CAM Subsystem Tests : Begin

POST: CAM Subsystem Tests : End, Status Passed

POST: Ethernet Controller Tests : Begin

Failed data line test (4).

addr=0x00000,sent=0x10000000 recv=0x800000000

POST: Ethernet Controller Tests : End, Status Passed

INIT: failed satellites initializationcisco WS-C3550-24-PWR (PowerPC) processor (revision L0) with 65526K/8192K bytes of memory.

Processor board ID CAT0923X1TK

Last reset from warm-reset

Running Layer2/3 Switching Image

Ethernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfaces

Ethernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfaces

Ethernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interface

Ethernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface

Ethernet-controller 4 failed POST

POST error status : external RAM test failed

The password-recovery mechanism is enabled.

384K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:14:6A:7B:86:80

Motherboard assembly number: 73-8100-09

Power supply part number: 341-0029-03

Motherboard serial number: CAT09240JXN

Power supply serial number: DTH09206Z8S

Model revision number: L0

Motherboard revision number: A0

Model number: WS-C3550-24PWR-SMI

System serial number: CAT0923X1TK

!!! WARNING: The switch is not usable !!!

The failed post are as follows

POST: Ethernet Controller Tests : Begin

Failed data line test (4).

addr=0x00000,sent=0x10000000 recv=0x800000000

POST: Ethernet Controller Tests : End, Status Passed

Ethernet-controller 4 failed POST

POST error status : external RAM test failed

Can someone please guide me where the problem is and how it can be solved ???

I am facing the same problem in a total of 12 switches

Thanx in advance

Sreesh

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

Re: Switch not working

Hello,

usually that means that there is a hardware problem, and that the switch has to be returned and replaced. Below is the explanation from Cisco itself.

Where did you buy those switches ? Are they new, and do you still have a warranty ?

A POST failure usually means that there is physical damage to the interface. If an Ethernet Controller which controls four interfaces fails, it results in the failure of those ports. A common cause of

such damage is ESD.

Failure of any of these diagnostic tests is normally fatal and usually requires a Return Material Authorization (RMA) to resolve the problem.

To be sure of this, reset the switch with a console connection established and capture the actual bootup diagnostic information, then create a service request with Cisco Technical Support.

Regards,

GP

2 REPLIES
VIP Purple

Re: Switch not working

Hello,

usually that means that there is a hardware problem, and that the switch has to be returned and replaced. Below is the explanation from Cisco itself.

Where did you buy those switches ? Are they new, and do you still have a warranty ?

A POST failure usually means that there is physical damage to the interface. If an Ethernet Controller which controls four interfaces fails, it results in the failure of those ports. A common cause of

such damage is ESD.

Failure of any of these diagnostic tests is normally fatal and usually requires a Return Material Authorization (RMA) to resolve the problem.

To be sure of this, reset the switch with a console connection established and capture the actual bootup diagnostic information, then create a service request with Cisco Technical Support.

Regards,

GP

New Member

Re: Switch not working

Dear GP,

The switches comes froma lot of about 154nos. of 3550 switches procured from cisco thru HCL Inc. They are brand new and still comes under the warranty period from Cisco.

Thanx for the advise, i think i should seriously take up the issue now with th management

Regards,

Sreesh

771
Views
0
Helpful
2
Replies
CreatePlease to create content