hello guys
we have a cat4006 wit SUP2 and 2 L3 modules any L3 module hat 34 Port FE
my prob ist how to configure it. to build VLAN with 3 (3548 XL) Etage.
pleas see the config
thankx for any Help
L3 Config:
RT4006WL23>en
RT4006WL23#sh run
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname RT4006WL23
!
!
ip subnet-zero
!
!
!
interface Port-channel1
no ip address
no ip redirects
no ip directed-broadcast
hold-queue 300 in
!
interface Port-channel1.2
encapsulation dot1Q 123
ip address 10.61.254.27 255.255.255.248
no ip redirects
no ip directed-broadcast
!
interface Port-channel1.3
encapsulation dot1Q 413
ip address 10.61.64.1 255.255.255.0
no ip redirects
no ip directed-broadcast
!
interface FastEthernet1
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet1
description UPLING1OG
ip address 10.61.66.1 255.255.255.0
no ip redirects
no ip directed-broadcast
!
interface GigabitEthernet2
description UPLING2OG
ip address 10.61.65.1 255.255.255.0
no ip redirects
no ip directed-broadcast
!
interface GigabitEthernet3
no ip address
no ip directed-broadcast
no negotiation auto
channel-group 1
!
interface GigabitEthernet4
no ip address
no ip directed-broadcast
no negotiation auto
channel-group 1
!
router ospf 1
area 0.0.0.0 authentication
passive-interface FastEthernet1
network 10.61.64.0 0.0.0.255 area 0.0.0.0
network 10.61.65.0 0.0.0.255 area 0.0.0.0
network 10.61.66.0 0.0.0.255 area 0.0.0.0
network 10.61.254.0 0.0.0.255 area 0.0.0.0
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.61.254.28
!
arp 127.0.0.2 0007.0ebb.dc00 ARPA
!
line con 0
transport input none
line aux 0
line vty 0 4
login
!
end
--------------------------------------------------------------------
L3 Config
SW4006WL23 (enable) set prompt SW4006WL23>
SW4006WL23> (enable) sh conf
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
.......
..................
....................
....................
..
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Tue Apr 9 2002, 06:56:58
!
#version 6.1(1)
!
!
#system web interface version(s)
set prompt SW4006WL23>
!
#test
!
#frame distribution method
set port channel all distribution mac both
!
#vtp
set vtp domain GAB
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 123 name VLAN-Transf-MUE-WL23 type ethernet mtu 1500 said 100123 state active
set vlan 411 name VLAN-WL23-1OG type ethernet mtu 1500 said 100411 state active
set vlan 412 name VLAN-WL23-2OG type ethernet mtu 1500 said 100412 state active
set vlan 413 name VLAN-WL23-3OG type ethernet mtu 1500 said 100413 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#ip
set interface sc0 413 10.61.64.4/255.255.255.0 10.61.64.255
set interface sl0 down
set interface me1 down
!
#syslog
set logging console disable
set logging level cops 2 default
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat4000.6-1-1.bin
!
#mls
set mls nde disable
!
#port channel
set port channel 3/1-3 156
!
#module 1 : 2-port 1000BaseX Supervisor
set vlan 413 1/1-2
set udld enable 1/1-2
!
#module 2 : 34-port Router Switch Card
set vlan 123 2/3
set vlan 412 2/4-34
!
#module 3 : 34-port Router Switch Card
set vlan 411 3/3-34
set trunk 3/1 nonegotiate dot1q 1-1005
set trunk 3/2 nonegotiate dot1q 1-1005
set port channel 3/1-2 mode on
!
#module 4 empty
!
#module 5 empty
!
#module 6 empty
end
SW4006WL23> (enable)
