12-18-2002 05:45 AM - edited 03-02-2019 03:41 AM
Hallo,
in the moment we are using 11.2 on an C1603 with an WIC-1B-S/T-LL .
We have an D64S connected to this WIC.
The question is:
Can we connect with, IOS 11.3.3T or higher, a D64S02 (Two B-Channels)
to the WIC-1B-S/T-LL with the following configuration:
isdn leased-line BRI1
int bri 1:1
ip address 10.1.1.1 255.0.0.0
int bri 1:2
ip address 20.1.1.1 255.0.0.0
regards
Karlheinz
12-19-2002 05:37 AM
Hi,
I suggest to use dialer-pools.
12-19-2002 12:35 PM
Hi,
what do you meen with using dialer-pools??????????
The question is:
Does the LL-WIC in an C1603 with 11.3(3)T or higher support
two separat B-channels and can i use at the same time the
integratet BRI as an dialer interface!!!!!!!!!!1
regards
Kalle
12-20-2002 01:49 AM
Hi,
You can use the two seperate B-channels for two different calls. Below, a small example. You can bring both channels up at the same time.
int bri 0
encapsulation ppp
ppp authentication chap
dialer pool-member 1
dialer pool-member 2
no ip address
...
int dialer 1
ip address 10.1.1.1 255.0.0.0
encapsulation ppp
dialer remote-name XXXX
dialer string XXXX
ppp authentication chap
int dialer 2
ip address 20.1.1.1 255.0.0.0
encapsulation ppp
dialer remote-name XXXX
dialer string XXXX
ppp authentication chap
12-20-2002 02:04 AM
Hallo,
i think there are some missunderstandings because i am
talking about leased lines (not dialer) with the WIC-LL modul.
The WIC-LL Modul is then BRI 1 and cann only handle leased-lines.
The question again is:
When i get an D64S2 or D64S02 (Two separat leased-line to the same
location) from our provider "TELEKOM" does i can configure this both
B-Channels separat like:
isdn leased-line bri1
int bri 1:1
ip add.......
int bri 1:2
ip add....
I know that you can configure "isdn leased-line bri1 128" with 11.3(3)T
or higher but this is only working in Japan.
regards
Karlheinz
12-26-2002 08:18 AM
First, you can use the integrated BRI as a dialer - what you do with the WIC does not effect the integrated BRI.
The WIC can be used for 64k or 128K service (I actually believe that DS02 is for 144K leased lines on a BRI (D+B+B)). However, this is for a single pipe/leased line only, the HW is not capable of considering both channels as separate leased lines. So you request would not work, you would instead require a separate WIC for each leased line.
12-29-2002 09:15 AM
Thanks for your answer.
My last question, can i use the internal BRI for leased line (two separat B-channels)?
And can i use then an separat WIC as an dialer interface?
I ask this because i saw a configuration like this except an separat WIC
as dialer interface.
12-20-2002 01:52 AM
Sorry forgot to add the following commands:
int d1
dialer pool 1
dialer-group 1
int d2
dialer pool 2
dialer-group 1
dialer-list 1 prot ip permit.
Please take a look at the cisco web-site for detailed info.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: