Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Hallo,

in the moment we are using 11.2 on an C1603 with an WIC-1B-S/T-LL .

We have an D64S connected to this WIC.

The question is:

Can we connect with, IOS 11.3.3T or higher, a D64S02 (Two B-Channels)

to the WIC-1B-S/T-LL with the following configuration:

isdn leased-line BRI1

int bri 1:1

ip address 10.1.1.1 255.0.0.0

int bri 1:2

ip address 20.1.1.1 255.0.0.0

regards

Karlheinz

7 REPLIES
New Member

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Hi,

I suggest to use dialer-pools.

New Member

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Hi,

what do you meen with using dialer-pools??????????

The question is:

Does the LL-WIC in an C1603 with 11.3(3)T or higher support

two separat B-channels and can i use at the same time the

integratet BRI as an dialer interface!!!!!!!!!!1

regards

Kalle

New Member

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Hi,

You can use the two seperate B-channels for two different calls. Below, a small example. You can bring both channels up at the same time.

int bri 0

encapsulation ppp

ppp authentication chap

dialer pool-member 1

dialer pool-member 2

no ip address

...

int dialer 1

ip address 10.1.1.1 255.0.0.0

encapsulation ppp

dialer remote-name XXXX

dialer string XXXX

ppp authentication chap

int dialer 2

ip address 20.1.1.1 255.0.0.0

encapsulation ppp

dialer remote-name XXXX

dialer string XXXX

ppp authentication chap

New Member

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Hallo,

i think there are some missunderstandings because i am

talking about leased lines (not dialer) with the WIC-LL modul.

The WIC-LL Modul is then BRI 1 and cann only handle leased-lines.

The question again is:

When i get an D64S2 or D64S02 (Two separat leased-line to the same

location) from our provider "TELEKOM" does i can configure this both

B-Channels separat like:

isdn leased-line bri1

int bri 1:1

ip add.......

int bri 1:2

ip add....

I know that you can configure "isdn leased-line bri1 128" with 11.3(3)T

or higher but this is only working in Japan.

regards

Karlheinz

Bronze

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

First, you can use the integrated BRI as a dialer - what you do with the WIC does not effect the integrated BRI.

The WIC can be used for 64k or 128K service (I actually believe that DS02 is for 144K leased lines on a BRI (D+B+B)). However, this is for a single pipe/leased line only, the HW is not capable of considering both channels as separate leased lines. So you request would not work, you would instead require a separate WIC for each leased line.

New Member

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Thanks for your answer.

My last question, can i use the internal BRI for leased line (two separat B-channels)?

And can i use then an separat WIC as an dialer interface?

I ask this because i saw a configuration like this except an separat WIC

as dialer interface.

New Member

Re: Two separate B-Channels w/WIC-1B-S/T-LL in an C1603

Sorry forgot to add the following commands:

int d1

dialer pool 1

dialer-group 1

int d2

dialer pool 2

dialer-group 1

dialer-list 1 prot ip permit.

Please take a look at the cisco web-site for detailed info.

110
Views
2
Helpful
7
Replies