Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

upgrade to GSR

I have a GSR running 12.0(21)S2 IOS, with following LC:

GE-GBIC-SC-B=, 40C3/ATM-MM-SC=, 8FE-TX-RJ45-B= and LC-4OC3/POS-SM=. I need upgrade the IOS version to the 12.0(21)ST6, but in the documentation say that these LCs are support in the release 12.0(8)S or higher.

Can i load the IOS 12.0(21)ST6 on this GSR with these LCs ?

2 REPLIES
Cisco Employee

Re: upgrade to GSR

You need to stick with S releases (like 12.0(21)S) to get all those cards supported. Pl. run hardware software compatibility matrix located at following url to get the informtation of all the cards supported in perticular release on a perticular platform.

http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi

Select product family and ios and click on submit, the tool will give you all the card supprted on that release.

New Member

Re: upgrade to GSR

yes, the sw advisory say that i must have a S release. But this same GSR with the same HW 1 year ago was running the 12.0(18)ST release and this is the output show version command from that time:

server120#sh version

Cisco Internetwork Operating System Software

IOS (tm) GS Software (GSR-P-M), Version 12.0(18)ST, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Thu 09-Aug-01 21:20 by nmasa

Image text-base: 0x60010950, data-base: 0x6246A000

ROM: System Bootstrap, Version 11.2(17)GS2, [htseng 180] EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTLDR: GS Software (GSR-P-M), Version 12.0(18)ST, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

server120 uptime is 22 weeks, 2 days, 9 hours, 59 minutes

System returned to ROM by abort at PC 0x6035D4BC at 06:33:36 UTC Fri Aug 31 2001

System restarted at 07:30:43 UTC Mon Oct 1 2001

System image file is "slot0:gsr-p-mz.120-18.ST.bin"

cisco 12008/GRP (R5000) processor (revision 0x05) with 262144K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

2 Route Processor Cards

2 Clock Scheduler Cards

3 Switch Fabric Cards

1 Quad-port OC3c ATM controller (4 ATM).

1 four-port OC3 POS controller (4 POS).

1 Single Port Gigabit Ethernet/IEEE 802.3z controller (1 GigabitEthernet).

1 eight-port FastEthernet/IEEE 802.3u controller (8 FastEthernet).

9 Ethernet/IEEE 802.3 interface(s)

1 GigabitEthernet/IEEE 802.3 interface(s)

4 ATM network interface(s)

4 Packet over SONET network interface(s)

507K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x2102

Then, I don´t understand Why the advisory show that is necessary a S release for this device.

regards,

Carlos

80
Views
0
Helpful
2
Replies