Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Urgent help needed : DIALUP Connection to Australia

Hi,

I have a 3640 router with bri's in a routary group, i have a problem connecting to a cisco 803 isdn router. the 803 router is in australia and iam trying to connect from switzerland. The connection from the router 803 in australia to the router in switzerland is working good ( iam calling from australia using the following tel. nr. format 0011+ the tel.nr in switzerland including the international code. the problem is that i can not set a connection from switzerland to the router in australia, iam using the usual code for australia 0061 + the tel.nr. of the isdn interface of the 803 router. when try to make the connection i get the following deb. output ( debug isdn q931).

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 193.72.77.153, timeout is 2 seconds:

5d23h: ISDN BR0 Q931: TX -> SETUP pd = 8 callref = 0x3F

Bearer Capability i = 0x8890

Standard = CCITT

Transer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x83

Called Party Number i = 0x80, '0061260567934'

Plan:Unknown, Type:Unknown

5d23h: ISDN BR0 Q931: RX <- SETUP_ACK pd = 8 callref = 0xBF

Channel ID i = 0x89.

5d23h: ISDN BR0 Q931: RX <- DISCONNECT pd = 8 callref = 0xBF

Cause i = 0x8781 - Unallocated/unassigned number

Facility i = 0x91A11A02021A4C0201233011300FA10D810346522EA20681010082010

1

- ETSI Supplementary Service, Invoke, AOC-E Currency

Display i = 'FR. 0.00'

5d23h: ISDN BR0 Q931: TX -> RELEASE pd = 8 callref = 0x3F

Cause i = 0x8081 - Unallocated/unassigned number

5d23h: ISDN BR0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xBF

5d23h: ISDN BR0 Q931: TX -> SETUP pd = 8 callref = 0x40

Bearer Capability i = 0x8890

Standard = CCITT

Transer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x83

Called Party Number i = 0x80, '0061260567934'

Plan:Unknown, Type:Unknown

5d23h: ISDN BR0 Q931: RX <- SETUP_ACK pd = 8 callref = 0xC0

Channel ID i = 0x89....

Success rate is 0 percent (0/5)

TIGER#

5d23h: ISDN BR0 Q931: RX <- DISCONNECT pd = 8 callref = 0xC0

Cause i = 0x8781 - Unallocated/unassigned number

Facility i = 0x91A11A02021A4E0201233011300FA10D810346522EA20681010082010

1

- ETSI Supplementary Service, Invoke, AOC-E Currency

Display i = 'FR. 0.00'

5d23h: ISDN BR0 Q931: TX -> RELEASE pd = 8 callref = 0x40

Cause i = 0x8081 - Unallocated/unassigned number

5d23h: ISDN BR0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xC0

-

can somebody help

Thanks

Ali

1 REPLY
Cisco Employee

Re: Urgent help needed : DIALUP Connection to Australia

Its a telco issue. You can see the cause "Unallocated/unassigned number" which means telco can't route the call to destination based on the number dialed. So verify with local telco to see the number dialed 0061260567934 is correct. May be the format is wrong.

204
Views
0
Helpful
1
Replies
CreatePlease login to create content