Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

vip4-80 FE subinterfaces oid

Hi.

I want to gather the bandwith utilisation on some subinterfaces in one FE PA instaled in a vip4-80.

When I snmpwalk our router it returns only the physical interfaces. I can see any subinterfaces.

The PA is:

PA Bay 0 Information:

Fast-Ethernet PA, 1 ports, 100BaseTX-ISL

EEPROM format version 1

HW rev 1.04, Board revision B0

If somebody know how can I monitor the bandwith utilisation for subinterfaces please let me know.

For vip2-40 with other FE PA it's work fine, i can see the subinterfaces but for this i can't

Thank You,

Otto

1 ACCEPTED SOLUTION

Accepted Solutions
Blue

Re: vip4-80 FE subinterfaces oid

Support for the above was added in 12.2(10)T and later.

3 REPLIES
Blue

Re: vip4-80 FE subinterfaces oid

What IOS version are you using?. Also are these FE sub-interfaces?. If so, what encap?

New Member

Re: vip4-80 FE subinterfaces oid

Hi Rizwan,

We use 12.2(2) T.

Yes they are FE sub-interfaces.

Encapsulation dot1.q.

Look if i snmpwalk our router it returns the folowing interfaces description only:

For FastEthernet 0/0/0 we have 11 sub-interfaces but i can't see this interfaces.

interfaces.ifTable.ifEntry.ifDescr.22 = Null0

interfaces.ifTable.ifEntry.ifDescr.31 = Loopback0

interfaces.ifTable.ifEntry.ifDescr.32 = Tunnel0

interfaces.ifTable.ifEntry.ifDescr.61 = Tunnel1

interfaces.ifTable.ifEntry.ifDescr.77 = FastEthernet0/0/0

interfaces.ifTable.ifEntry.ifDescr.78 = Serial0/1/0

interfaces.ifTable.ifEntry.ifDescr.138 = Serial12/0/0

interfaces.ifTable.ifEntry.ifDescr.139 = Serial12/0/1

interfaces.ifTable.ifEntry.ifDescr.140 = Serial12/0/2

interfaces.ifTable.ifEntry.ifDescr.141 = Serial12/0/3

interfaces.ifTable.ifEntry.ifDescr.142 = FastEthernet2/0/0

interfaces.ifTable.ifEntry.ifDescr.143 = Serial10/0/0

interfaces.ifTable.ifEntry.ifDescr.144 = Serial10/0/1

interfaces.ifTable.ifEntry.ifDescr.145 = Serial10/0/2

interfaces.ifTable.ifEntry.ifDescr.146 = Serial10/0/3

interfaces.ifTable.ifEntry.ifDescr.147 = FastEthernet4/0

interfaces.ifTable.ifEntry.ifDescr.150 = Tunnel10

interfaces.ifTable.ifEntry.ifDescr.151 = Loopback1

interfaces.ifTable.ifEntry.ifDescr.152 = Tunnel1001

interfaces.ifTable.ifEntry.ifDescr.154 = Tunnel101

interfaces.ifTable.ifEntry.ifDescr.156 = Tunnel6001

interfaces.ifTable.ifEntry.ifDescr.157 = FastEthernet2/1/0

interfaces.ifTable.ifEntry.ifDescr.158 = FastEthernet2/1/0.1

interfaces.ifTable.ifEntry.ifDescr.159 = FastEthernet2/1/0.2

interfaces.ifTable.ifEntry.ifDescr.160 = FastEthernet2/1/0.3

interfaces.ifTable.ifEntry.ifDescr.161 = FastEthernet2/1/0.5

interfaces.ifTable.ifEntry.ifDescr.162 = FastEthernet2/1/0.6

interfaces.ifTable.ifEntry.ifDescr.163 = FastEthernet2/1/0.8

interfaces.ifTable.ifEntry.ifDescr.164 = FastEthernet2/1/0.9

interfaces.ifTable.ifEntry.ifDescr.165 = FastEthernet2/1/0.10

interfaces.ifTable.ifEntry.ifDescr.166 = FastEthernet2/1/0.11

interfaces.ifTable.ifEntry.ifDescr.167 = FastEthernet2/1/0.12

Thank you

Otto

Blue

Re: vip4-80 FE subinterfaces oid

Support for the above was added in 12.2(10)T and later.

102
Views
0
Helpful
3
Replies
CreatePlease to create content