Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Voip call via Gatekeeper is disconnected due to "0x80E6 - Recovery on timer expiry"

2 as5300 as gateways and a 2620 as a gatekeeper is used for voip connections. If I use as session target ipv4 the appropriate ip address of the router at the far end the call is connected through. If I use as session target the gatekeeper - ras - then the call setup is started but disconnected with the message below. At the moment only 1 AS5300 is configured with appropriate dial-peers but both AS5300 are successfully registered to the gatekeeper.

<p>

2w3d: RIP (seq# 32344) rcvd

2w3d: ISDN Se0:15: RX <- DISCONNECT pd = 8 callref = 0x1238

2w3d: Cause i = 0x80E6 - Recovery on timer expiry

2w3d: ISDN Se0:15: TX -> RELEASE pd = 8 callref = 0x9238

2w3d: cc_api_call_disconnected(vdbPtr=0x61FDE904, callID=0x146, cause=0x66)

2w3d: sess_appl: ev(12=CC_EV_CALL_DISCONNECTED), cid(326), disp(0)

2w3d: cid(326)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_DISCONNECTED)

oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(1)fDest(1)

2w3d: -cid2(327)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_MAPPING)

2w3d: ssaDiscSetting

2w3d: ssaFlushPeerTagQueue cid(326) peer list: (empty)

2w3d: ssa: Disconnected cid(326) state(1) cause(0x66)

2w3d: ccCallDisconnect (callID=0x146, cause=0x66 tag=0x0)

2w3d: ccCallDisconnect (callID=0x147, cause=0x66 tag=0x0)h323chan_dgram_send:Sen

t UDP msg. Bytes sent: 76

to 217.71.109.98:1719

2w3d: RASLib::GW_RASSendDRQ: DRQ (seq# 32345) sent to 217.71.109.98

2w3d: cc_api_call_disconnect_done(vdbPtr=0x61FDE904, callID=0x146, disp=0, tag=0

x0)

2w3d: sess_appl: ev(13=CC_EV_CALL_DISCONNECT_DONE), cid(326), disp(0)

2w3d: cid(326)st(SSA_CS_DISCONNECTING)ev(SSA_EV_CALL_DISCONNECT_DONE)

oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(1)fDest(1)

2w3d: -cid2(327)st2(SSA_CS_DISCONNECTING)oldst2(SSA_CS_MAPPING)

2w3d: ssaDisconnectDone

<p>

Gateway config:

dial-peer voice 100 voip

destination-pattern 45T

voice-class codec 100

session target ras

tech-prefix 45#

ip precedence 5

no vad

interface Ethernet0

ip address 192.50.109.99 255.255.255.248

h323-gateway voip interface

h323-gateway voip id gk-Berlin.cisco.com ipaddr 192.50.109.98 1718

h323-gateway voip h323-id GW-test-B1@cisco.com

h323-gateway voip tech-prefix 45#

gatekeeper

zone local gk-Berlin.cisco.com cisco.com 192.50.109.98

zone remote gk-test.cisco.com cisco.com 10.3.20.15 1719

zone prefix gk-test.cisco.com 45_

no shutdown

1 REPLY
Anonymous
N/A

Re: Voip call via Gatekeeper is disconnected due to "0x80E6 - Re

The description is confusing, you said you have two as5300s and one gatekeeper, but in the config,

you have local zone and a remote zone of gk-test: 10.3.20.15.

Not quite sure what the real topology is. Try not to use tech-prefix under dial-peer for routing purpose first.

139
Views
0
Helpful
1
Replies